Zelmer ZVC425 Series, User Manual

Page: 48 / 51

48
ZVC425-004_v01
18 Parquet brush “BNB” (in types: ZVC425HQ, ZVC425XT,
ZVC425HT, ZVC425SP)
Is used to clean and polish hard, scratch sensitive
surfaces such as wooden floors, floor panels, parquet,
marble, tiles, etc.
Delicate and soft natural bristles ensure maximum
vacuum effectiveness and protects against scratching
the cleaned surface.
19 Small nozzle
20 Small brush
21 Crevice nozzle
22 Switchable combination brush
23 Turbobrush (in type ZVC425HT)
24 Electrobrush (in type ZVC425HQ)
25 Mini turbobrush (in types: ZVC425HM, ZVC425SA)
26 Suction nozzle for mattresses cleaning (in types:
ZVC425XT, ZVC425HM, ZVC425HA)
27 Brush for collecting pet hair from carpets (in types:
ZVC425SA, ZVC425HA)
Preparing the vacuum cleaner
for operation
1 Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2
Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device “A” and slide the tube into the hose handle so that
the locking device “A” is blocked in opening “B” .
3 Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5 Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according to
the figure . Retract the brush when vacuuming carpets
(set the switch in “ ”).
6
The vacuum cleaner is equipped with locker for
accessories. In order to open the locker, pick up the handle
of vacuum cleaner and pull upwards the cover of the locker
for accessories (10) .
7 The accessories may be attached to the accessory
holder in the suction hose handle. This way they will be
available for use at any time.
8
The button of power cable coiler is located under the
handle of vacuum cleaner (from the right). This place has
been marked by the sign on the handle. Press the handle
in marked place and pull out the cable.
9
Plug in the appliance.
B
Before operation make sure that the SAFBAG bag is
installed in the vacuum cleaner chamber and that inlet filter
and the HEPA/EPA outlet filter is installed in the appliance.
11
Switch on the vacuum cleaner by pressing the “on/off”
button (6) .
11 The vacuum cleaner is equipped with electronic power
regulator allowing a stepless regulation of vacuum cleaner
power. The power regulation is performed with a slider.
12
Moving the slider according to its mark (+ or –) will
increase or reduce the suction power.
Filter disassembly
Before changing the filters make sure that the vacuum cleaner
is switched off and unplugged from the mains supply.
INLET FILTER
1 Release the catch of front cover (11) and open it.
2
Remove the SAFBAG dust bag module from the vacuum
cleaner chamber.
3 Put out the cover of inlet filter together with installed inlet
filter from the guide rails located on back wall of vacuum
cleaner chamber.
4
Take out the inlet filter from the inlet filter cover.
5 Put the new filter into inlet filter cover (16) . Pay attention
whether the edges of filter cling closely to the cover of filter.
6 The cover of inlet filter (16) together with installed filter
press home into guide rails to the previous location.
The damaged inlet filter should be replaced
with a new, genuine manufactured product
only.
7 Insert the SAFBAG dust bag module to the vacuum
cleaner chamber.
8
Close the cover by pressing it until you hear
a characteristic click – pay attention not to trap the dust bag.
HEPA/EPA OUTLET FILTER
The vacuum cleaners are equipped with a HEPA H13/EPA
E11 outlet filter.
1 In order to change the outlet filter HEPA/EPA pick up the
handle of vacuum cleaner and open the locker for accessories.
2
Press the catch on outlet filter cover, then put out the
outlet filter cover from the vacuum cleaner.
3 Remove the outlet filter HEPA/EPA cassette, replace the
used cassette with new one. The HEPA/EPA filter assure circa
1 year of effective usage.
4
Put the filter cover this way that three ledges placed
in lower part of cover hit the gaps in the vacuum cleaner
casing, and the upper ledge is snapped.
●
Close the locker for accessories and move down the
handle.
C
D