Zelmer ZJE1000I, User Manual

Page: 51 / 54

53
JE1000-001_v07
After each use
1 Switch off the appliance, turning the switch (4) to „0” .
2
Unplug the appliance.
●
Disassemble the appliance. Proceed as described above in
section “Preparing for operation (disassembling)” ( Fig. B ).
Prevent overfilling the pulp container. Excess
pulp can spill out while leaning the container
on disassembly.
Cleaning and maintenance
●
If water or juice leaks into the inside of the motor unit,
abort operation immediately and have the appliance
checked at the service centre.
●
Wash the appliance thoroughly after every use to prevent
adhesion of juice and pulp to the walls.
●
Wipe the housing with a damp cloth with a few drops of
washing liquid.
●
Wash the following elements in warm soapy water:
pulp container, juice bowl, lid, pusher and jug with froth
separator. You can also wash them in a dishwasher at
max. 60°C.
●
Use the brush (16) to remove dirt from crevices and
corners of the appliance. After the motor has stopped
completely, disassemble the appliance and wash all of
its parts (see Fig. B ). Remove the pulp from the pulp
container. Wash the strainer only with the brush supplied
with your appliance (16) . Do not try to use any metal
brushes for washing the strainer!
●
Some parts of the appliance may change colour after
long-term use. It is not a defect.
●
Orange stains from carrot juice can be removed
by cleaning the surface with a cloth immersed in
cooking oil.
●
Dry all parts thoroughly after washing.
●
Reassemble the appliance according to instructions
provided above ( Fig. C ).
●
Store the power cord inside the base of the drive unit.
Troubleshooting
My juice extractor does not work:
●
Plug another household appliance into the same wall
socket to find out if it works or not.
●
Have the juice extractor checked at the service centre.
The appliance extracts little juice or vibrates:
●
Switch off the appliance, remove pulp residue from the
strainer filtration net. Empty the pulp container if full.
●
Replace the strainer if broken.
Preparing healthy and delicious juice
●
Fruit and vegetables for juice extraction process should
be fresh and well washed. Vegetables should be cleaned
of sand and soil under running water and peeled.
E
Assembling the appliance
1 Place the juice bowl (8) on the motor unit (1) , inserting
the spout (9) in the opening of the motor unit casing.
2 Mount the strainer (11) on the skimmer (7) , press it all
the way in, and check if it is well mounted and swivels easily.
3 Place the lid (12) on the juice bowl (8) .
4 Lift up both clamps (5) and fix them on to the fasteners
(6) located on the lid.
5 Press the clamps (5) to the motor unit (1) (you will hear
a characteristic click).
6
To mount the pulp container (10) under the lid (12) ,
proceed as follows: lean the pulp container (10) and place
it under the juice bowl (8) . Then slide it in towards the motor
unit (1) . Place the Jug (14) under the spout (9) .
If you fail to assemble any of the parts (e.g. the
juice bowl, lid, pulp container or locking
clamps) or do it improperly, a safety device will
prevent the switch-on of the appliance.
Starting and operating the juice
extractor
●
Make sure that the power on/off button is set to “0” .
●
Unwind a sufficient length of the cord. The remaining
cord can be stored inside the drive housing. Slip the
remaining cord through an opening located at the side
of the appliance.
1 Insert the power cord (3) plug into the socket and
press the on/off button (4) to start the appliance, selecting
speed level 1 (position I – low rotation speed for soft fruit
and vegetables such as raspberries, tomatoes, cucumbers,
melons, etc.) or level 2 (position II – high speed rotation for
hard fruit or vegetables such as carrots, celery, apples, etc.).
See a table on page 52 for detailed information
(examples) on the recommended speed level for different
fruit and vegetables.
2 Insert pieces of fruit or vegetable into the feeder tube on
the lid (12) and guide them gently through with the pusher (13) .
Never insert foreign objects or your fingers
into the feed tube.
●
Transfer the extracted juice from the container into
glasses, cups, etc.
●
The jug (14) has a froth separator (15) to stop the dense
juice fractions and the froth when the juice is distributed
into other receptacles.
Feel encouraged to drink the juices as they are,
without removing the naturally occurring pulp
and froth. It is not recommended to remove the
froth separator from the jug.t
C
D