55
B
Appliance elements
1
Outlet filter cover
2
Handle
3
Plug and cord
4
Combination brush fastening
5
Infrared receiver (type 5500.3)
6
Power increase button
7
ON/OFF button
8
Power decrease button
9
Suction power level indicator
10
Filling indicator device for dust bag/dust container
„CYKLON”
11
Cord rewind knob „Autorevers“
12
Cord rewind button
13
Electrobrush socket
14
Outlet filter wear indicator
15
Front cover fastening
16
Accessory compartment cover
17
Infrared transmitter (type 5500.3)
18
STANDBY mode button (type 5500.3)
19
Suction hose. The vacuum cleaner is equipped with one
suction hose (A or B)
A
Suction hose (type 5500.0)
B
Suction hose with remote power control (type 5500.3)
20
Telescopic suction tube
21
Basic HEPA filter (installed in the vacuum cleaner)
22
Basic filter protective mesh (installed in the vacuum
cleaner)
23
“CYKLON” dust container
24
SAFBAG dust bag
25
SAFBAG dust bag module (with the installed SAFBAG
dust bag)
26
Outlet filter HEPA H13 (installed in the vacuum cleaner)
27
Acoustic foam (built in the vacuum cleaner)
28
Inlet filter casing (installed in the vacuum cleaner)
29
Inlet filter (installed in the vacuum cleaner)
30
Small brush
31
Crevice nozzle
32
Small nozzle
33
Parquet brush “BNB”
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles, etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
34
Turbobrush (type 5500.0 HT, 5500.3 HT)
35
Electrobrush (type 5500.0 HQ, 5500.3 HQ)
36
Combination brush. The vacuum cleaner is equipped
with only one type of combination brush (A or B)
A
Switchable combination brush
B
Combination brush with a small item separator
Preparing the vacuum cleaner for
operation
The Solaris Twix vacuum cleaner has two alternative dust
collecting modules which can be selected by the user:
The bagless “CYKLON” dust container with the HEPA
–
filter – where the dust is “whirled” and deposited in the
container.
The SAFBAG dust bag module – the dust is accumulated
–
in a disposable bag with high filtration quality.
1
Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2
Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device
“A”
and slide the tube into the hose handle so that
the locking device
“A”
is blocked in opening
“B”
.
3
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5
You may assemble a basket for picking up small objects in
the combination brush with the small item separator. In order
to do so remove the blank cover and insert the basket.
6
To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure
.
7
Grab the plug
(3)
and pull the cord out of the vacuum
cleaner.
ATTENTION! While puling out the cord pay attention
to the yellow stripe which signals the end of the
cord. Further attempts (pulling on cord) may result in
damaging the cord.
The vacuum cleaner is equipped with an „Autorevers“
function, which provides automatic cord rewinding without
necessity of constant pressing the cord rewind knob
(12)
.
In order to start up the function, move the „Autorevers”
(11)
knob to position
AUTO
.
8
Plug in the appliance.
Before launching the vacuum cleaner make sure whether the
SAFBAG bag module or „CYKLON” dust container has been
installed in chamber of vacuum cleaner. Make also sure
whether all filters have been installed in vacuum cleaner.
9
Switch on the vacuum cleaner by pressing the “on/off”
button
(7)
.
10
The vacuum cleaner is equipped with an electronic power
control which allows to gradually adjust the vacuum cleaner
suction power during operation. To adjust the suction power use
the power adjustment buttons
(6,8)
– to increase the suction
power or – to decrease the suction power. The suction power
setting is indicated by the appropriate number of lit diodes.
The vacuum cleaner will by default begin operation at the
medium power range. 3 diodes will light on the suction power
level indicator
(9)
.
A
