59
5500-003_v02
1
Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2
Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device
“A”
and slide the tube into the hose handle so that
the locking device
“A”
is blocked in opening
“B”
.
3
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5
You may assemble a basket for picking up small objects
in the combination brush with the small item separator.
In order to do so remove the blank cover and insert the
basket.
6
To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure
.
7
Grab the plug
(3)
and pull the cord out of the vacuum
cleaner.
While puling out the cord pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
The vacuum cleaner is equipped with an „Autorevers“
function, which provides automatic cord rewinding without
necessity of constant pressing the cord rewind knob
(12)
.
In order to start up the function, move the „Autorevers”
(11)
knob to position
AUTO
.
8
Plug in the appliance.
Before launching the vacuum cleaner make sure whether the
SAFBAG bag module or „CYKLON” dust container has been
installed in chamber of vacuum cleaner. Make also sure
whether all filters have been installed in vacuum cleaner.
9
Switch on the vacuum cleaner by pressing the “on/off”
button
(7)
.
10
The vacuum cleaner is equipped with an electronic power
control which allows to gradually adjust the vacuum cleaner
suction power during operation. To adjust the suction power
use the power adjustment buttons
(6,8)
– to increase the
suction power or – to decrease the suction power. The
suction power setting is indicated by the appropriate number
of lit diodes.
The vacuum cleaner will by default begin operation at the
medium power range. 3 diodes will light on the suction power
level indicator
(9)
.
The suction power may be adjusted during operation.
The recommended settings are:
Setting 1 – vacuuming curtains
Setting 2 – vacuuming upholstery
Setting 3 – cost-effective power
Setting 4 – vacuuming carpets
Setting 5 – vacuuming hard floors and crevices.
11
The vacuum cleaner type 5500.3 is additionally equipped
with remote suction power control located in the suction hose
handle. It allows to change the suction power without the
necessity to bend down.
In order to use this function, open the battery compartment
in the suction hose handle and insert two 1.5 V AAA type
batteries or two chargeable 1.2 V AAA type batteries.
Insert the batteries so that the battery pole
marked ” is always directed towards
the lock of the compartment marked with “+”.
Use only high quality batteries. Battery leakage may
cause damage to the electronic system.
12
To use the remote control of the suction power press the
appropriate button on the hose handle ( , ):
To increase the suction power by one setting press the
–
button
.
To decrease the suction power by one setting press the
–
button
.
13
Press the button on the hose handle to temporarily
switch off the appliance and to operate in the
STANDBY
mode.
To continue vacuuming press the
STANDBY
button
(18)
once
again. The appliance will start operating with the previously
set suction power.
The infrared transmitter and receiver have to
“see” each other in order for the remote control
system to work properly.
14
The vacuum cleaner is equipped with accessories
compartment. In order to open the compartment pull up the
cover of the accessories compartment
(16)
.
15
The accessories may be attached to the accessory
holder in the suction hose handle. This way they will be
available for use at any time.
16
The vacuum cleaner is equipped with the “Parksystem”
function. This function allows to temporarily switch off the
vacuum cleaner using the fastening hook of the combination
brush without the necessity to use the on/off button. In order
to do so, during operation insert the fastening hook of the
combination brush in the combination brush fastening
(4)
.
The vacuum cleaner will automatically switch off.
Filter disassembly
This vacuum cleaner is equipped with a filter attachment with
cyclonic filtration that allows the vacuum cleaning without
conventional dust bag. The characteristic feature of cyclonic
filter is that occurrence of air-stream rotation is applied to
separation of solid pollutants. The separation of pollutants
is performed inside the part of circular section container,
in which the rotating air rejects the pollutants towards
container’s wall and then the pollutants are being removed
to neighboring container chamber through the outlet. The
initially cleaned air is directed towards cone shaped filter
HEPA, which holds the smallest dust fractions. The filter