Zelmer IR2200, User Manual

Page: 84 / 88

84
IR2200-001_v02
●
The iron is ready for use.
4
Aim the steam nozzle at the creased fabric or curtain.
Press the Steam Burst Button – steam will shoot from the
holes of the soleplate.
5 For Stubborn wrinkles, wait a few seconds before
pressing the Steam Burst Button again .
Most wrinkles can be removed within three
presses.
It may be necessary to press the Steam Burst
Button several times to start this function.
For optimum steam quality, do not press the
Steam Burst Button more than three times in
a row.
When ironing delicate fabrics (synthetics, silk,
velvet etc.), keep the iron a few centimetres
away from the garment to prevent damage.
ENDING THE IRONING
1
Turn the Temperature Dial counter-clockwise to “ MIN ”
position. The will turn off.
2 Set the steam control to position.
3
Unplug the unit.
4 Empty the water tank. See „Emptying The Water Tank”.
5 When the iron has cooled completely, store it vertically in
a safe place.
Emptying The Water Tank
●
Set the Steam Control to position.
●
Unplug the unit.
1 Hold the iron upside down and shake it gently to remove
the remaining water.
2 When the soleplate is still hot, press the Steam Burst
Button to drain the water tank.
3 Press the Spray Button to release any remaining water.
●
Before storing the iron, make sure the Steam Control is
set to position.
Additional Functions
ANTI SCALE SYSTEM
The appliance has a build-in anti-limescale container.
It is designed to reduce the build-up of limescale which
occurs during steam ironing.
The build-in anti-scale cartridge prolongs
the service life of the iron. However, it will
not completely stop the natural process of
limescale build-up.
C
SELF CLEANING
This function provides for removal of scale and mineral
built-up in the Steam Chamber. The performance of the iron
largely depends on the water hardness and the frequency
of performing the self-cleaning process. It is recommended
to perform self-cleaning at least once a month or more
regularly.
1 Proceed as described in the “Before First Use” section.
2
Turn the Temperature Dial to „●●●“.
3 The Heater Light will come on.
The light will go off once the required
temperature is reached.
●
The iron is ready for use.
4 Wait for one more cycle. The light will go on and off.
5 Turn the Temperature Dial counter-clockwise to ‘ MIN ’
position.
6 Unplug the unit.
7 Hold the iron horizontally over a sink.
8 Press and hold the Self-Cleaning Button .
9
Steam and boiling water will flow out of the holes
on the soleplate, washing away the scales and minerals
accumulated inside the steam chamber.
10 Sway the iron gently until the water tank is empty.
11
Release the Self-Cleaning Button when self cleaning is
complete.
12 Place the iron on a flat and level surface and allow it to
cool down completely.
13 Wipe the soleplate with a cold damp cloth.
The water flowing out of the soleplate is very
hot. Take extra care when performing the self-
clean operation.
ANTI DRIP
●
The anti-drip system is designed to prevent water leaking
from the soleplate when the iron is not sufficiently hot.
●
When engaged, the anti drip system may produce
a clicking sound, particularly during heat-up or when the
iron is cooling down. This is normal and indicates that the
system is working correctly.
AUTO OFF
The iron has an auto-off feature in vertical and horizontal
position which activates automatically when the appliance is
plugged in and left unattended.
1 The iron will shut-off automatically after about 30
seconds of inactivity if left on its soleplate (in horizontal
position) and after about 8 minutes in vertical position.
2
The Auto-Off Light will pulse (flash) which indicates that
the iron is in the automatic shot-off mode.
3 Move the unit to continue ironing. The iron will go back to
the previous settings and will heat-up again.