14
Place of installation:
Must be free of frost and on level ground.
Connections:
Intake connection (optimal 3 pcs.), types SWH 100/190
-
Nipple to connect a hose, diameter ¾”(20mm)
-
Gasket at the top to the connect pipes, diameter 40mm with a spline end which alleviated the mounting of the intake
connecting(scope of delivery)
-
The washing machine connection has to be slipped over the hose nipple!
-
The pipe inlet connection with a diameter of 50mm for shower is located sideward at the container. It is locked with a dummy
plug. The inbuilt height amounts 80mm. It is usable from booth sides through turning the box. To connect a shower, make
sure that the shower tray is set high enough to create sufficient drop (min. 15 cm).
-
Intakes not used have to be sealed and blanked off!
Connections of pressure pipes:
There is a back draft damper built in the lifting unit. The pressure pipe has a thread socket G1 ¼” FT at its end. Please take care that the
screwed connection of the pressure pipe does not balk the port for the back draft damper. The pressure pipe has to be fitted with a flexible
hose at the mounted piping. It is possible to disconnect the pressure piping from the screw joint for maintenance work. Please ensure the non
return valve is fitted to the system discharge port.
Ventilation and odour prevention:
This lifting unit is designed with active carbon filter assignment and may not need any separate ventilation. Self evident, it is possible to
install separate ventilation pipe with a diameter of 40mm. For this case remove the integrated valve- filter (carbon filter, valve insert, ball)-
unit.
Commencement of operation:
Before starting up check all pipe connections for correct mounting, please. Now plug the SWH unit into an electrical outlet and check the
function by letting water go into the container. At this point, check the tightness of the intake. After the refloating of the float switch the
pump will be switched on automatically. The discharge pipe tightness has to be checked for leaks while pump is operating. The pump will be
switched off automatically by the float switch when the water level is at its lowest. Water must not run back from the pressure pipe to the
container.
6. Maintenance / Service
Always disconnect from power before servicing!
Service and repair at electrical parts of the pump (cable, motor) has to be done by authorised service- companies
or producer.
In case of very low temperatures and in any case before the first frost the pump must be removed from water.
Empty the pump and store it in a place where it is protected from frost.
The lifting unit has to be cleaned regularly. For checking and cleaning the lifting unit disconnect the pressure pipe and the intakes from the
cover. Then detach the clips from the cover. After this the cover with pump has to lift up. The container, the intake strainer, the float switch
and the ventilation bore hole at the pump have to be cleaned to avoid malfunction and clogging by solids and by contamination.
In case of using washing machines without strainer the lifting unit has to be cleaned in shorter intervals, and especially the ventilation bore
hole and the intake strainer.
Repair service kits and service tools are available on request. You will find a topical overview about our service partners at
www.zehnder-pumpen.de.
We explicitly mention that spare parts and accessories which are not delivered and checked by Zehnder are not permissible. The built in and
use of such products may negatively affect the constructive set properties under these circumstances. For damages which arise by using of
non-original spare parts and accessories, Zehnder will refuse any liability and warranty. For faults which you can not repair by yourself you
should contact our customer service or a qualified person.
Please replace the cover with pump into the container and lock them with the both clip closures after the cleaning. The clip closures have to
be placed in the cover at first and then down at the container.
7. Warranty
This pump carries a 24 month manufacturer warranty. The warranty period begins with the date of purchase by the end user. Proof of
purchase should be retained. Within this period we will remove all kind of shortcoming due to failures of material or assembling. It is up to
us either to repair or to replace the pump.
This warranty does not cover damage cause by improper use or wear and tear (mechanical seal). Also, there will be no warranty given in case
of unauthorised repair of the pump.
Consequential damages caused by failing of the pump are not covered by the manufacturer.
GB
B
