manualshive.com logo in svg

ZCS 3PH 100KTL-HV, User Manual

Share
Download
ZCS 3PH 100KTL-HV User Manual Download Page 43

 

          43 / 67 

User’s Manual 3PH 100KTL-136KTL-HV 
Rev. 1.0 24/02/2021 

Identification: MD-AL-GI-00 
Rev. 1.0 of 24/02/2021 - Application: GID 

 

4)

 

Measure PV voltage of DC input with multimeter, verify DC input cable polar and connect DC connector 
with inverter until hearing a slight sound indicated connection succeed. 

 

 

 

 

 

Figure 36 - DC cable connection 

 

 

 

Note: Please use multimeter to make sure the PV array positive pole and negative pole!

 

 
Dealing

：

If  need  to  remove  the  PV  connector  from  inverter  side,  please  use  the  Removal  Tool  as  below 

diagram, move the connector gently. 

 
 

Removal procedure

 

To remove the positive and negative connectors from the inverter, insert a removal tool in the bayonet 
coupling and press the tool with adequate force, as shown in the figure below. 

 

 
Before  removing  the  positive  and  negative  connectors,  make  sure  that  the 
inverter’s circuit breaker is switched off. If not, the direct current may cause an 

electric arc that could result in a fire 

 

Warning

 

 

Summary of Contents for 3PH 100KTL-HV




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands