manualshive.com logo in svg

ZCS 3PH 100KTL-HV, User Manual

Share
Download
ZCS 3PH 100KTL-HV User Manual Download Page 4

 

          4 / 67 

User’s Manual 3PH 100KTL-136KTL-HV 
Rev. 1.0 24/02/2021 

Identification: MD-AL-GI-00 
Rev. 1.0 of 24/02/2021 - Application: GID 

General instructions 

This  manual  contains  important  safety  instructions  that  must  be  followed  during  installation  and 
maintenance of the equipment. 

Please keep these instructions! 

This manual  must  be  considered  an  integral  part  of  the  equipment,  and must  be  available  at  all  times  to 
everyone who interacts with the equipment. The manual must always accompany the equipment, even when 

it is transferred to another user or plant. 

Copyright statement 

Copyright of  this manual  belongs  to  Zucchetti Centro  Sistemi  S.p.A. No  part  of  this  manual  (including  the 

software,  etc.)  may  be  copied,  reproduced  or  distributed  in  any  form  or  by  any  means  without  the 
permission  of  Zucchetti  Centro  Sistemi  S.p.A.  All  rights  reserved.  ZCS  reserves  the  right  to  final 

interpretation. This manual is subject to change based on feedback from users, installers or customers.    
Please check our website 

http://www.zcsazzurro.com

 for the latest version. 

Technical support 

ZCS  offers  a  support  and  technical  consultancy  service  accessible  by  sending  a  request  directly  from  the 
website https://www.zcsazzurro.com/it/support. 

For the Italian territory, the following toll-free number is available: 800 72 74 64. 
 

 

 

Summary of Contents for 3PH 100KTL-HV




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands