background image

10

470

30

591

380

140

360 cm

2

50 cm

2

120 cm

2

180 cm

2

30

20 min

60

a

b

POSSIBILITIES FOR

INSERTION

Kitchen unit with door

Proper  arrangements  must  be

taken in designing the forniture unit,

in order to avoid any contact with

the bottom of the hob which can be

heated when it is operated. The

recommended solution is shown in

Fig. 14.

The panel fitted under the hob

should be easily removable to allow

an  easy  access  if  a  technical

assistance intervention is needed.

Kitchen unit with oven

The hob recess dimensions must

comply the indication given in Figs.

15 and 18 and must be provided

with brackets to allow a continuous

supply of air.

To avoid overhating, the building in

should be carried out as shown in

Figs. 16 e 17.

The hob's electric connection and

the oven's one must be carried out

separately, both for safety reasons

and to allow the oven to be easily

taken off the unit.

Hanging forniture units or hoods

must  be  placed  at  650  mm.

minimum from the hob (Fig. 19).

a) Removable panel

b) Space possibly useful for

connections

550 min.

560 min.

Fig. 14

Fig. 15

Fig. 16

Fig. 17

Fig. 18

FO  1013

FO  0947

FO  0938

FO  0939

FO 0198

Fig. 19

650 mm

FO  2099

Summary of Contents for ZGLR 646













Reviews: