background image

2

• This appliance has been designed to be operated by

adults and children under supervision. Young children

MUST

 

NOT

 be allowed to tamper with the controls or

play near or with the oven.

• This  appliance    has  been  designed  for  cooking

edible foodstuff and to be used for domestic  non-

professional purposes only. It must not be used for

any other purpose.

• It is 

dangerous 

to alter the specification in any way.

• For hygiene and safety reasons, this appliance should

be kept clean at all times. A build-up of fats or other

foodstuff could result in a fire.

• Accessible parts of this appliance may become hot

when it is in use. Children should be 

KEPT

 

AWAY

 until

it has cooled.

• Under no circumstances should you attempt to repair

the  appliance  yourself.  Repairs  carried  out  by

unexperienced persons may cause injury or serious

malfunctioning. Refer to your local Zanussi Service

Centre.  Always  insist  on  genuine  Zanussi  spare

parts.

• Ensure that all control knobs are in the OFF position

when not in use.

• Should you connect any electrical tool to a plug near

this cooking appliance, ensure that electric cables

are not in contact with it and keep them far enough

from the heated parts of this appliance.

•

If the appliance is out of order, disconnect it from the

electric supply.

These instructions are only for the countries stated by the symbol

printed on the front cover of this instruction book.

This appliance complies with the following

E.E.C. Directives:

- 73/23

 - 

90/683

 (Low Voltage Directive);

- 89/336

 (Electromagnetical Compatibility Directive);

-

90/396

 (Gas Appliances)

- 93/68

 (General Directives)

and subsequent modifications.

During Operation

About Installation, Cleaning

and Manteinance

• It is mandatory that all operations required for the

installation are carried out by a qualified or competent

person,  in  accordance  with  existing  rules  and

regulations.

• Disconnect the appliance from the electrical supply,

before  carrying  out  any  cleaning  or  manteinance

work.

• Ensure a good ventilation around the appliance. A

poor air supply could cause lack of oxygen.

• Ensure that the gas supply complies with the gas

type stated on the identification label, placed near

the gas supply pipe.

•

Using a gas cooking appliance will produce heat

and  moisture  in  the  room  which  it  has  been

installed  in.  Ensure  a  continuous  air  supply,

keeping  the  air  vents  in  good  conditions  or

installing a cooker hood with discharge tube.

•

In  case  of  intensive  or  long  time  use  of  the

appliance, make the ventilation more efficient,

by opening a window or increasing the electric

exhaust fan power.

• Once you removed all packaging from the appliance,

ensure that it is not damaged and the electric cable

is  in  perfect  conditions.  Otherwise,  contact  your

dealer before proceeding with the installation.

• The manufacturer disclaims any responsability

should  all  the  safety  measures  not  be  carried

out.

MANUFACTURER:

ELECTROLUX ZANUSSI S.p.A.

Viale Bologna 298 - 47100 FORLI’ (Italy)

For Your Safety

These warnings are provided in the interest of safety. You 

MUST

 read them carefully before

installing or using the appliance.
It is most important that this instruction book should be retained with the appliance for future

reference. Should the appliance be sold or transferred, always ensure that the book is left

with the appliance in order that the new owner can get to know the functions of the appliance

and the relevant warnings.

F

Summary of Contents for ZGLR 646













Reviews: