background image

31

1. Instruction for the User

HOB BURNERS CONTROL KNOBS

The hob burners control knobs are situated on the hob
front panel. The symbols on the knobs mean that :

  ●

there is no gas supply

 

there is maximum gas supply

  

there is minimum gas supply

LIGHTING THE BURNERS

For easier lighting, proceed before putting a pan
on the pan support.

Approach the burner with a flame. (In models provided
with electric ignition, depress the relevant switch marked
with a small spark). Then, push the relevant knob down
and turn it anti-clockwise until it reaches the "maximum"
position.
Check the flame is regular and adjust it as required.
If you cannot light the flame even after several attempts,
check the "cap" (Fig. 1 lett. A) and the "crown" (Fig. 1 lett.
B) are in the correct position.
To put the flame out, turn the knob to the symbol 

.

Always turn the flame down or put it out before
taking the pans off the burner.

USING THE HOB CORRECTLY
To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottom fitting the size of the burner used, so that flame
will not spread beyond the bottom of the vessel (see the
table beside).
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.

Use only pans or pots with flat bottom.

Carefully supervise cookings with fats or oil,
since these types of foodstuff can result in a fire,
if over-heated.

Burner

minimum

maximum

diameter

diameter

Big (rapid)

160 mm.

240 mm.

Small (Auxiliary)

80 mm.

160 mm.

Fig. 1

Contents

1. Instruction for the User ............. Pag.

31

2. Cleaning and Maintenance ....... Pag.

32

3. Technical Data ........................... Pag.

32

4. Instruction for the Installer ....... Pag.

33

5. Electrical Connection ................ Pag.

34

6. Adaptation to different

types of gas ................................ Pag.

35

7. Building In .................................. Pag.

36

Guarantee ................................... Pag.

38

FO 0204

Table of minimum and maximum diameters of
pots which can be placed on the burners

Summary of Contents for ZAF2










Reviews: