background image

About these installation guidelines

4

Multitronic-Retrofit Kit_01_2004-06-16

About these installation guidelines

These installation guidelines contain basic information on the safe use of the
control system.

Characters and symbols used

  Work steps that you have to carry out in the sequence stated are marked by

black triangles.

„

 

Lists are marked by a small box.

Note:

These notes provide you with hints and information on the safe and
efficient handling of machines and devices.

Warning!

These safety notes warn against damage to property and help you to avoid
such damage.

Danger!

These danger notes with a grey background warn against personal injury
and/or danger to life and limb; danger notes help you to avoid serious or
life-threatening situations for yourself and/or third parties.

Target group of these installation guidelines

These instructions have been specifically drawn up for persons involved in the
installation, configuration and maintenance of the control system. We assume
that these persons are

„

 

trained technical staff, e.g. electricians, who

„

 

have already carefully read and fully understood the summary operating
instructions of the summary operating manual of the 

Multitronic

 control

system.

Installation guidelines: handling

These installation guidelines must be continuously available at the site where the
control system is used. We recommend to prepare a copy and to keep the same
in a safe and freely accessible place next to the control system.  Keep the
original document in a safe place.

Summary of Contents for Multitronic

















Reviews: