background image

9

ANSWERING AN ENTRANCE PANEL CALL

When a visitor presses the Call button on the entrance panel, all connected indoor 
displays will sound the call chime at the same time as the INCOMING CALL message 
on each display screen. Touch the 

 icon to answer the call. Touch 

 again to send 

the calling entrance panel camera feed to all other displays. If you touch 

 before 

the call is switched by a user of another display in the system, you will return to the 
calling visitor. If the call is not answered by the time the call chime stops, the display 
will enter standby mode. Touch the 

 icon to release the electric catch of the calling 

entrance panel during the call. The display will show DOOR OPEN. Touch the XXX 
icon to open the gate. The display will show GATE OPEN. If another caller tries  
to reach you during your call, the display will show VISITOR AT DOOR 2. Touch  
the   icon to answer and switch to the second call.
Note: Touch and hold the 

 icon during an entrance call or an internal call (display-

to-display intercom mode) to mute your microphone. The display will show MUTE. 
Touch and hold 

 again to unmute your microphone, which the display will confirm 

with SPEAK. Operating a gate requires the NC06 gate control module in the system.

VIDEO FEED MONITORING

With the display on standby, touch and hold 

 to monitor the video feed from 

entrance panel 1. Touch 

 again to switch to the next video feed.

The CCTV camera video feeds can only be monitored this way if the Port 4 status  
is Enabled (see Table SYSTEM SETTINGS, item 10).
Touch   to start a voice call with the visitor at the entrance panel from which you are 
monitoring the video feed. Touch 

 to unlock the door of the same entrance panel.

When monitoring the video feed from Door1/Door2/CCTV1/CCTV2, touch and hold 

 to change the screen aspect from 16:9 to 4:3.

PUBLIC ADDRESS MODE

The Public Address mode allows you to speak through all displays connected  
to the video entry phone system. When the display is on standby, touch and hold  

 on the screen. The PUBLIC ADDRESS CALL message will be displayed. All other 

displays in the system will display PUBLIC ADDRESS. You can now speak and be 
received by other displays in the system. Touch 

 to exit the public address mode.

Summary of Contents for VP-816B













Reviews: