Z3 Technology Z3-DM816X-RPS RDK User Manual Download Page 59 | Manualshive

Page: 59 / 67

background image

CONFIDENTIAL

DOC-USR-0026-02

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

59

UBI: MTD device name: "File System"
UBI: MTD device size: 200 MiB
UBI: number of good PEBs: 1601
UBI: number of bad PEBs: 0
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 1601
UBI: number of PEBs reserved for bad PEB handling: 48
UBI: max/mean erase counter: 2/0
UBI: image sequence number: 920932318
UBI: background thread "ubi_bgt0d" started, PID 40
davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
davinci_mdio davinci_mdio.0: detected phy mask fffffffc
davinci_mdio.0: probed
davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown
davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver unknown
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v1.0.0)
OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
notify_init : notify drivercreated for remote proc id 2 at physical
Address 00
Registered tvp5158 audio codec
asoc: tlv320aic3x-hifi <-> davinci-mcasp.2 mapping ok
asoc: HDMI-DAI-CODEC <-> hdmi-dai mapping ok
asoc: tlv320aic3x-hifi <-> davinci-mcasp.1 mapping ok
asoc: adv7611-hifi <-> davinci-mcasp.0 mapping ok
asoc: adv7611-hifi <-> davinci-mcasp.1 mapping ok
ALSA device list:
#0: TI81XX EVM
#1: APP02
TCP cubic registered
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
omap_voltage_late_init: Voltage driver support not added
Power Management for TI81XX.
omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC
(946684800)
davinci_mdio davinci_mdio.0: resetting idled controller
net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01,
id=1cc915)

«
...
57
58
59
60
61
...
»

Summary of Contents for Z3-DM816X-RPS RDK




































































Reviews:

No comments

Related manuals for Z3-DM816X-RPS RDK

Brand: VADDIO Pages: 2

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Samson Pages: 20

Brand: Watts Pages: 8

CentriPro Aquavar SOLO

Brand: Xylem Pages: 48

Brand: PUTCO Pages: 2

Brand: WAC Pages: 5

Brand: Greenheck Pages: 4

Brand: Swagelok Pages: 16

Brand: DAYLIFF Pages: 40

TRULUX DMX 3Z Touch Control

Brand: American Lighting Pages: 2

Brand: Lucci comfort Pages: 3

Brand: RTI Pages: 2

Brand: MIT Pages: 20

Brand: Zenith Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands