Z3 Technology Z3-DM816X-RPS RDK User Manual Download Page 2

Page: 2 / 67

CONFIDENTIAL

DOC-USR-0026-02

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

Revision History

Version

Date

Change Note

Author

1.00.00

07/18/13

Initial Version

RL/RC

1.01.00

07/30/13

Added more information

1.01.01

08/02/13

Formatting

2.00.23

02/09/14

Updated to reflect latest version, added sections on RTP encode,
dynamically changing bit rate, TS rate, tuning for low latency, DHCP,
and performing a decode. Added parameter lists.

2.00.23a

02/12/14

Corrected reference errors on pages 8 and 17, corrected figures on
pages 17 and 34.

2.01.19

06/01/14

Changed name from DM816X-RPS RDK -> DM816X-RPS RDK. Updated
screenshots. Added info on ZFinder.

Summary of Contents for Z3-DM816X-RPS RDK




































































Search results

Summary of Contents for Z3-DM816X-RPS RDK

Reviews:

Related manuals for Z3-DM816X-RPS RDK

Brands by name

Popular brands

Z3 Technology Z3-DM816X-RPS RDK, User Manual

Search results

Summary of Contents for Z3-DM816X-RPS RDK

Reviews:

Related manuals for Z3-DM816X-RPS RDK

Brands by name

Popular brands