Z3 Technology Z3-DM816X-RPS RDK User Manual Download Page 18

Page: 18 / 67

CONFIDENTIAL

DOC-USR-0026-02

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

(2)

Connect the supplied 2.5mm serial cable and NULL modem adapter to your PC.

(3)

Take the HDMI cable connected to the monitor and connect it to HDMI In 1 of the board.

(4)

Connect the Ethernet

The next step is to set up a terminal to view the activity of the board …

5.3

Set up the Terminal Window

(5)

If you are running from a Windows PC, run TeraTerm. Select “Setup – Serial Port” and set the

following:

Port:

Whichever serial port the port is connected to

Baud Rate: 115200

Data:

8-bit

Parity:

None

Stop:

1-bit

Flow Control: None

(6)

If you are running from Linux, type:

# sudo minicom –s

And then configure by doing the following:

-Select “Serial Port Setup”

-Ensure the right Serial Device is specified (typically “/dev/ttyUSB0”)

-Set option E (“Bps/Par/Bits”) to 115200 8N1

-Press <return>

-Select “Exit”

5.4

Power on the board

(7)

Connect the 12V power supply and turn on the switch. If all is configured properly, you should see the

board booting up within the terminal window. After about a minute, you will see the RPS Main Menu:

Summary of Contents for Z3-DM816X-RPS RDK




































































Search results

Summary of Contents for Z3-DM816X-RPS RDK

Reviews:

Related manuals for Z3-DM816X-RPS RDK

Brands by name

Popular brands

Z3 Technology Z3-DM816X-RPS RDK, User Manual

Search results

Summary of Contents for Z3-DM816X-RPS RDK

Reviews:

Related manuals for Z3-DM816X-RPS RDK

Brands by name

Popular brands