Z3 Technology HE4K-DCK-10 User Instructions Download Page 18

Page: 18 / 76

HE4K-DCK-10 User Instructions

DOC-USR-0123-01

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

6.2.2

Run VLC to View RTP Stream

An SDP file is needed to view an RTP stream from the HE4K-DCK-10 in the VLC media player.

If you have

not yet downloaded these files to your computer, you can find them at

Z3Cam-4K.Z3technology.com

Note:

Verify your PC is set up to handle decode of H.265 content at 4K resolutions. See Section 9.1, “PC

Configuration for 4K HEVC/H.265 Decode”, for more information.

(1)

Open the VLC media player on your PC.

(2)

Select the

Media

menu.

(3)

Select

Open File

(4)

Find and select the SDP file corresponding to the video codec you selected previously.

H265(HEVC) video: use the SDP file entitled “z3-h265-he4k-dck.sdp”

H264(AVC) video: use the SDP file entitled “z3-h264-he4k-dck.sdp”

(5)

Press

Enter

or click

Open

. You will see your camera’s video streaming to VLC.

Figure 12 Example of Encoded Video Streaming to VLC (RTP)

Summary of Contents for HE4K-DCK-10













































































Search results

Summary of Contents for HE4K-DCK-10

Reviews:

Related manuals for HE4K-DCK-10

Brands by name

Popular brands

Z3 Technology HE4K-DCK-10, User Instructions

Search results

Summary of Contents for HE4K-DCK-10

Reviews:

Related manuals for HE4K-DCK-10

Brands by name

Popular brands