manualshive.com logo in svg

Yunca Gas EROS, User Manual

Share
Download
Yunca Gas EROS User Manual Download Page 3

25-07-01 

Page 3 of 23                      Operation Instructions for Eros Free Standing Gas Fire July 2001.doc

 

 

 
 

INTRODUCTION

                                                                                                                     

Welcome and congratulations on purchasing your YUNCA EROS FLUED GAS HEATER.

 

Please read the following carefully before attempting to operate the heater and ensure all 
members of your home understand how this elegant and highly efficient heater functions. 
 
 
Please fill out and return the registration card promptly.  
 
 
These instructions should be stored in a convenient safe place for ready reference.  If you have 
any questions regarding your heater please contact your YUNCA EROS dealer. 
 
 
The YUNCA EROS FLUED GAS HEATER is a listed gas-fired, conventionally vented, room 
heater tested by independent laboratories to New Zealand standards. 
 
 
The installation of the YUNCA EROS FLUED GAS HEATER must be carried out by a suitably 
qualified person and comply with the current New Zealand (Australian installation code) NZS 
5261:1996  (AG 601:1998) 
 
 
 

CAUTION

:

 

This appliance must be flued to atmosphere

. Installation and repair of the 

YUNCA EROS VENTED GAS HEATER should be done by a qualified person. The appliance 
should be serviced at least annually by a qualified service person.  Control valve compartments, 
burners, fan, and air circulating passageways of the EROS must be kept free from any lint and 
dust build-up to ensure efficient and safe operation of the heater. 
 

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE. 
 
DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE. 
 
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS 
OPERATIONAL. 

 
To remove internal packaging, refer to page 12 for front door removal.  
 

Summary of Contents for EROS
























Reviews:

No comments

Brands by name

Popular brands

Load more brands