manualshive.com logo in svg

Yunca Gas EROS, User Manual

Share
Download
Yunca Gas EROS User Manual Download Page 16

25-07-01 

Page 16 of 23                      Operation Instructions for Eros Free Standing Gas Fire July 2001.doc

 

 

 

 

Fault Finding: 

 

SYMPTOM                           

 

PROBLEM  

 

CORRECTIVE 

Pilot Will Not Light.

 

No spark at pilot burner.

 

Check connection between 
electrode in pilot assembly 
and lead from control. Press 
connection hard together. 
(Inserted 18mm in to control) 
 
Replace the pilot assembly if 
ceramic insulator is cracked or 
broken. (Finger tighten nut 
that holds ceramic insulator)

 

 

Gas not available at the spark 
point. A complete ring of gas 
around the pilot hood. 

Clean the gas ways of soot or 
foreign particles 
 
Open up the gas gap where the 
spark earth’s on to the pilot.

 

 

Spark gap is incorrect. 

 

Spark gap should be 3-4mm 
between the electrode tip and 
the pilot flame hood. 

 

 

No gas at pilot burner

 

Check that isolating valves 
are turned on and gas is 
available. 
 
Check pilot hood for 
blockage 
 
Remove pilot jet and blow 
clean. The jet is located 
inside the base of the pilot 
burner and is removed by 
disconnecting the gas to the 
pilot and removing the brass 
nut from the base of the 
burner. Jet will fall out. 
 
Check for any obstructions in 
the gas line that may cause 
low pressure or restrict flow. 
 
Purge gas lines.

 

 

No Supply Gas. 

 

L.P.G. -- Refill tank 
Natural -- Check with gas 
supplier 

Summary of Contents for EROS
























Reviews:

No comments

Brands by name

Popular brands

Load more brands