manualshive.com logo in svg

Yunca Gas EROS, User Manual

Share
Download
Yunca Gas EROS User Manual Download Page 18

25-07-01 

Page 18 of 23                      Operation Instructions for Eros Free Standing Gas Fire July 2001.doc

 

 

top 8mm of the thermocouple.

 

Thermocouple not properly 
connected.

 

Check back of main control 
where thermocouples copper 
tube enters the control. 
Tighten brass collar nut.

 

 

Defective thermocouple.

 

Replace thermocouple 
A new thermocouple may be 
ordered through your 
YUNCA agent.

 

 

Faulty control valve.

 

A replacement may be fitted 
by a suitably qualified 
service person.

 

 

Pilot burning, no gas to 
burners 

 

Control turned to Pilot only 

 

Turn the control knob to on 
position 

 

Thermostat turned down 
below the room temperature 

Turn the thermostat up to a 
setting above room 
temperature. 
 
Move the thermostat bulb to 
a position that accurately 
senses the room temperature 
 

 

Burner injectors may be 
blocked. 

Disconnect gas supply at 
burners and unscrew brass 
injectors from end of burner. 
Use compressed air to clean 
out orifice. 

Back burner stays on when 
switched to off position.

 

Faulty control

 

Control requires replacement.

 

 

 

Build up on the control 
valve. 
 
 
 

 

Disassemble the control 
valve by removing the two 
screws below the cover. 
Extract the control valve, 
note the position. Clean the 
control valve clean and re-
assemble. Test operation. 

Summary of Contents for EROS
























Reviews:

No comments

Brands by name

Popular brands

Load more brands