background image

 

10

 

Battery Test

When you first connect the tester to the battery, it functions as a voltmeter 

until you press the 

ENTER

 button to start the test.  This function can be turned 

off through the Options Menu
After you press 

ENTER

, scroll to each parameter using the 

UP

 or 

DOWN 

ARROW

 button and press 

ENTER

 to select. If any messages appear during the 

test, see “Test Messages” 

1.  TEST TYPE: choose which test needs to be performed:
 

- YUASA warranty test

 

- Battery test

 

- New battery test

2. 

YUASA WARRANTY:
The Yuasa warranty test needs to be used whenever you want to send 

in a Yuasa battery for warranty purposes. When the test outcome is 

“Charge & Retest” the battery needs to be charged with an approved 

Yuasa charger.
BAT. LOCATION: Scroll to and select 

IN VEHICLE

 or OUT OF VEHI-

CLE for a battery not connected to a vehicle.  Following an IN VEHICLE 

test you will be prompted to test the starting and charging systems.

IMPORTANT:

 The performance of the starting and charging systems depends 

on the battery’s condition. It is important that the battery is good and 

fully charged before any further system testing.

BAT. AGE: Select 

new battery 

or

 in service

New battery: battery is fresh produced and not yet installed in a ve-

hicle. For instance: the battery is in a warehouse waiting for delivery 

to a customer.
In service: the battery is already used and cycled in the vehicle

3.  APPLICATION: scroll to and select AUTOMOTIVE, MOTORCYCLE, TRUCK.

4. 

BATTERY TYPE:

 scroll to and select 

REGULAR

 FLOODED, 

AGM FLAT PLATE

AGM SPIRAL, or 

GEL

 where applicable.

www.midtronics.com

Summary of Contents for MDX-617





















Reviews: