Yuasa MDX-617 Instruction Manual Download Page 14 | Manualshive

Page: 14 / 20

background image

•

14

•

Error Messages

Error Message

Interpretation

BATTERY POWER TOO

LOW TO USE PRINTER.

CONNECT TO FULLY

CHARGED BATTERY

11.50 TO 16.00V

Battery being tested has fallen below 9 volts.

Connect to a fully charged battery to use the

printer.

CONNECT TO

12V BATTERY

Tester is not connected to the battery

LOW INTERNAL AA

BATTERIES. REPLACE

AA BATTERIES SOON!

Internal AA batteries are low and need to be

replaced. See “Maintenance & Troubleshooting”

section.

NON 12 VOLT SYSTEM

DETECTED

System being tested is not 12-volts.

PRINTER DOOR OPEN.

CLOSE DOOR AND TRY

TO PRINT AGAIN

Door covering printer paper is not secure.

PRINTER OUT OF PAPER

REPLACE WITH THERMAL

PRINTER PAPER.

2.5 IN. DIA. MAX.

2.25 IN. WIDE MAX

Printer is out of thermal paper. Replace with new

roll. See “Maintenance & Troubleshooting” section.

QC DATA MEMORY FULL

PRINT RESULTS OR

CLEAR MEMORY.

QC mode memory is full. Select QC mode from the

Options Menu to clear the memory.

www.midtronics.com

«
...
12
13
14
15
16
...
»

Summary of Contents for MDX-617





















Reviews:

No comments

Related manuals for MDX-617

Brand: Cronyx Pages: 40

Brand: Stalwart Pages: 6

Brand: VOLTCRAFT Pages: 59

Brand: Kuman Pages: 11

Brand: U-Line Pages: 39

Brand: Motorola Pages: 73

Brand: Motorola Pages: 69

Brand: Keithley Pages: 24

Brand: protech Pages: 16

Brand: Craftsman Pages: 25

Brand: Craftsman Pages: 19

Brand: Craftsman Pages: 21

Brand: Tektronix, Inc. Pages: 102

Brand: Terahertz Technologies Pages: 11

Brand: Brandson Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands