background image

22 

Boss X-series  

Instructions for use 

23

youngmangroup.com 

 

5.2 loadIng and unloadIng

The BoSS X-Series machine may also be 
wheeled onto an adequately rated tail lift with 
the platform in the fully lowered position. The 
swivel castor brakes should then be applied, 
the tail lift raised, the brakes released and the 
machine wheeled onto the flat base of  the 
tail lift vehicle and the swivel castor brakes 
applied. The BoSS X-Series machine should 
be anchored to the vehicle by means of  straps 
passed through the forklift access points.

WarnIng

The forklift or tail lift used to lift the BoSS 

X-Series machine must be adequately rated.

The BoSS X-Series machine may be lifted by a 
crane or Hiab by threading adequately rated 
lifting straps through the forklift access points.

 

WarnIng

a full risk assessment must be carried out.

 

the straps must be threaded inside the 

guardrails of the machine.

5.4 PreParatIon for transPort

Prior to transporting the BoSS X-Series 
machine on a vehicle, ensure that the following 
precautions are taken:

a.

Ensure that the platform is fully lowered 
to its rest position

b.

Ensure that the handset control unit is 
secured to the platform and that the 
transit gate lock is engaged

c.

Ensure that both swivel castor brakes are 
applied

d.

Secure the BoSS X-Series machine 
to the transport vehicle using straps 
through each of  the forklift entry points 
as shown below

5.3 lIftIng

Summary of Contents for BOSS X Series




















Reviews: