Qingdao Desiree DTPO610VC Installation And Operation Manual Download | Manualshive

Page: 1 / 22

background image

1

Installation And Operation Manual

For

DTPO610VC

Forward this manual to all operators. Failure to operate this equipment as directed may cause injury.

INSTALLATION AND OPERATION MANUAL

TWO POST LIFT

MODEL NO.

DTPO610VC

Lifting Capacity

：

4.5T/10000lbs

Lifting Height

：

71in/1800mm

Motor

：

2.2kw./3hp

Keep this operation manual near the machine at all times. Make sure
that ALL USERS read this manual.

SHIPPING DAMAGE CLAIMS

When this equipment is shipped, title passes to the

purchaser upon receipt from the carrier. Claims for
the material damaged in shipment must be made by
the purchaser against the transportation company at
the time shipment is received.

BE SAFE

Your new lift was designed and built with safety in

mind. However, your overall safety can be increased
by proper training and thoughtful operation on the
part of the operator. DO NOT operate or repair this
equipment without reading this manual and the
important safety instructions shown inside.

1
2
3
...
»

Summary of Contents for DTPO610VC























Reviews:

No comments

Related manuals for DTPO610VC

Brand: Datavideo Pages: 17

Brand: Magmaweld Pages: 8

Brand: Magmate Pages: 20

Brand: Magliner Pages: 20

Brand: SanRex Pages: 4

Brand: ShoreStation Pages: 15

Brand: OMG Pages: 32

Brand: Lincoln Electric Pages: 102

Brand: Mahe Pages: 48

Drive 4 Basic S

Brand: EWM Pages: 52

Brand: WELTECH Pages: 41

Brand: WARPP Pages: 23

Digital Car Puller 5000

Brand: Telwin Pages: 104

Brand: OMEGA AIR Pages: 9

Brand: Lincoln Electric Pages: 56

Brand: Parweld Pages: 20

ePowerSwitch 8 Master

Brand: Neol Pages: 2

VIPER CUT 30Mk II

Brand: Xcel-Arc Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands