background image

Glow Plug Wire 

Diesel Time

18 sec

Page 16

Programming Menu Options

Feature

Unlock Before, Lock After Starting, 

Lock after remote start

Door Lock / Unlock Pulse Duration

Min. Crank Time for the 

Alternator Sensing

Driver’s Priority Unlock

Double Pulse Unlock

OFF

0.8 sec

0.8 sec

ON

2.5 sec

1.0 sec

OFF

OFF

ON

ON

Factory Default

Optional

Anti-Grinding Only

Lock Upon Reservation

Short Pluse Lock/ Unlock

Start-Kill Relay

0.125 sec

Anti-Gr 

Passive starter- kill

Active Lock Upon Reservation

OFF

OFF

Turbo

N/A

ON

Manual Transmission Lock

This is only of the manual transmission vehicle. With this option, 
you have to actively lock the vehicle after the manual transmission reservation.

Page 17

Some vehicles such as Mercedes-Benz and the Lexus ES300 require you to

unlock the car to disarm the factory alarm before remote starting the vehicle.
Activating this feature will unlock the vehicle for a brief second in order to          
disarm the factory alarm before auto-starting the vehicle remotely then 
lock after starting. 

This feature unlocks the driver s side door lock with the first unlock pulse.  
A second unlock pulse is need to unlock the rest of the car doors.                           

Turbo mode requires the connection of the emergency brake wire for either 
automatic or manual transmission vehicles.  With this mode, the engine will 
continue running for two minutes after the key is turned off if the emergency
brake was set  before the key was turned off and the foot brake was not 
being pressed when the key was turned off.

Use this feature if you do not use the glow plug wire. 

“With the Option Programmer, you can program between 3-99 seconds.”

This option will not be available if you chose 2.5 sec pulse 

der 1-2.

Passive Kill 

The factory setting for the starter-kill relay is Anti-Grinding only.

With this optional setting, you can add Passive Starter-kill function, that will be 
activated,
1) Whenever doors are locked by the remote, or
2) One minute after the ignition is off, or
3) 30 seconds after the last door is closed if the door trigger is installed and the 

user's option for Passive Locking (Button                for a half second) is 
turned on.  See Passive Locking of the User's Manual. 

You can deactivate the starter-kill with the Lock/Unlock button.

In order for this feature to operate, the installer must use the

2

nd

Unlock Wire (Or/Bk wire of Connector 4).  Isolate the driver s door actuator

from the rest of the other doors.  Call us for the technical support if you are not
sure about this.

The procedures will be same as the 4 button remotes except  the use 
of the different buttons. 

Programming 

6 Button Remote 4 Button Remote

ICON

(I+II)-

(I+IV)-

(IV)

( I )

( II )

( III )

(Trunk+Start)-
(Trunk+Stop)-

(Stop)-

Lock

Unlock

(Start)-

Programming Menu 1
Programming Menu 2

Option Selection

Factory Setting

Option Selection

Default Setting Selection

Option Programming for Six Button Remotes

Summary of Contents for 2WAMANT











Reviews: