background image

876572-BIM-C-0213

4

Johnson Controls Unitary Products

Installation

Limitations

These units must be installed in accordance with the following 
national and local safety codes.

1.

National Electrical Code ANSI/NFPS No. 70 or Canadian 
Electrical Code Part 1, C22.1 (latest editions).

2.

Local plumbing and waste water codes and other 
applicable local codes.

Refer to Table 6 for unit physical data and to Table 5 for electrical 
data.

If components are to be added to a unit to meet local codes, 
they are to be installed at the dealer's and/or the customer's 
expense.

Size of unit for proposed installation should be based on heat 
loss/heat gain calculations made in accordance with industry 
recognized procedures identified by the Air Conditioning 
Contractors of America.

Figure 1: Component Location

Direct Drive 

Condenser Fan Motor

High Efficiency Enhanced 

Copper Tube/Aluminum Fin

Outdoor Coil

High Efficiency 

Compressor Rigidly 

Mounted

Decorative Protective 

Coil Guard

High Efficiency Enhanced 

Copper Tube/Aluminum Fin 

Indoor Coil

Blower Service 

Access Panel

X13 or PSC 
Direct Drive 

Blower Motor

Refrigerant 

Connections

Control Box Service 

Access Panel

Heavy Gauge 

Base Rails

Table 1:

Unit Limitations

Size

(Tons)

Unit Voltage

Unit Limitations

Applied Voltage

Outdoor DB Temp

Min

Max

Max (°F)

024

(2.0)

208/230-1-60

187

252

125

030

(2.5)

208/230-1-60

187

252

125

036

(3.0)

208/230-1-60

187

252

125

208/230-3-60

187

252

125

042

(3.5)

208/230-1-60

187

252

125

048

(4.0)

208/230-1-60

187

252

125

208/230-3-60

187

252

125

060

(5.0)

208/230-1-60

187

252

125

208/230-3-60

187

252

125

460-3-60

432

504

125

Summary of Contents for UB0 Series





























Reviews: