background image

FIG. 10 - DIMENSIONS & CLEARANCES (Cont’d.)- DCE & DCG

DETAIL “X”

ACCESSORY SIDE SUPPLY AND RETURN AIR OPENINGS

DUCT COVERS - Units are shipped with the bottom
duct openings covered. An accessory flange kit is avail-
able for connecting side ducts.
For bottom duct applications:
1. Remove the side panels from the supply and return
     air  compartments to  gain access to  the bottom
     supply and return air duct covers.
2. Remove and discard the bottom duct covers. (Duct
     openings are closed with sheet metal covers except
    when the unit includes a power exhaust option. The
    covering consists of a heavy black paper composition.)
3. Replace the side supply and return air compartment
     panels.
For  side duct applications;
1. Replace the side panels on the supply and return air
    compartments with the accessory flange kit panels.
2. Connect ductwork to the duct flanges on the rear of
     the unit.

 

     39-5/8

FIXED OUTDOOR AIR OR
BAROMETRIC RELIEF RAIN HOOD

REAR VIEW

L.H. END VIEW

23-3/8" 2"

3-3/4"

28"

10-5/8"

27"

3/4" CONDENSATE
DRAIN
(MUST BE TRAPPED)

7"

(B) POWER W
      ENTRY

29-5/8"

3-1/2"

4-1/2"

71"

ECONOMIZER
RAIN HOOD

DETAIL “Y”

UNIT WITH RAIN HOODS

    66-1/2"

    36"

530.18-N11Y

12

Unitary Products Group

Summary of Contents for D1CE

























Reviews: