yellow jacket 40870 User Manual Download Page 4

 

Chapter 1: 

Before You Start 

 

Contacting Ritchie Engineering: 

To order accessories, receive assistance, or locate the nearest YELLOW JACKET

®

 distributor.

 

 

Corporate Office and Mailing Address: 

Ritchie Engineering Co, Inc. YELLOW JACKET

®

 Products Division  

10950 Hampshire Avenue South, Bloomington, MN 55438-2623 U.S.A.

 

Phone: (952) 943-1300 or (800) 769-8370 

Fax: (800) 769-8370 

E-mail: [email protected] 

www.yellowjacket.com

 

 

Safety Information: 

Use the instrument only as specified in this manual. Otherwise, the protection provided by the 

instrument may be impaired. Refer to safety information in Table 1-1.

 

 

A Warning identifies conditions and actions that pose hazards to the user. A Caution identifies 

conditions and actions that may damage the instrument or the equipment under test. 

 

 

Table 1-1. Safety Information 

Warning 

 

 

To avoid personal injury or death, follow these 

guidelines: 

 

 

Most governments and legal authorities    

re- quire that HVAC technicians be trained 

and certified in the safe and proper 

operation of HVAC tools, such as this 

instrument. Since this tool may be 

connected to many types of equipment 

through a limitless combination of hoses 

and fittings, proper training is the most 

important element of using this tool safely. 

 

 

Read the entire User Manual before using 

the instrument. 

 

 

Use the instrument only as described in the 

User Manual, otherwise the protection pro- 

vided by the equipment may be impaired. 

 

 

 

 

 

Do not use the instrument if it is damaged. 

Before you use the instrument, inspect the 

case. Look for cracks or loose components 

 

 

The instrument contains no internal user- 

serviceable parts; Do not open the 

instrument. Have the instrument serviced 

only by Ritchie Engineering Co. or 

authorized service centers. 

 

 

Do not use the instrument if it operates ab- 

normally. Protection may be impaired. 

When in doubt, have the instrument 

serviced. 

 

 

 

Summary of Contents for 40870
































Reviews: