Yealink SIP-T19P User Manual Download | Manualshive

Page: 26 / 124

background image

User Guide for the SIP-T19P IP Phone

16

will perform a PPP negotiation to obtain the IP address. Contact your system
administrator for the PPPoE user name and password.

To configure PPPoE via phone user interface:

1.

Press Menu->Settings->Advanced Settings (password: admin) ->Network->WAN
Port.

2.

Press to select IPv4 and press the Enter soft key.

3.

Press to select PPPoE IP Client and press the Enter soft key.

4.

Enter the user name and password in the corresponding fields.

5.

Press the Save soft key to accept the change or the Back soft key to cancel.

Note

Generally, your phone will be deployed with multiple other phones. In this case, your
system administrator will configure the phone parameters beforehand, so that after you
start up your phone, the phone will be registered and ready for use. If your phone is not
registered, you may have to register it. For more information on how to register your
phone, refer to

Account Registration

on page

50

.

If the phone has successfully started up, the idle screen will be shown as below:

The idle screen shows the label of current account, time and date, and four soft keys.

Using the wrong network parameters may result in inaccessibility of your phone and may
also have an impact on your network performance. For more information on these

parameters, contact your system administrator.

«
...
24
25
26
27
28
...
»

Summary of Contents for SIP-T19P





























































































































Reviews:

No comments

Related manuals for SIP-T19P

Brand: ZEN Pages: 62

Brand: Yealink Pages: 2

Brand: Safeline Pages: 32

Brand: United Security Products Pages: 24

SPH-A600 Series

Brand: Samsung Pages: 111

Skype V500DS-S1

Brand: Aztech Pages: 2

Brand: Vonino Pages: 87

Brand: Ecom Instruments Pages: 64

Brand: Alcatel Pages: 44

Brand: Kyocera Pages: 56

Brand: Sagem Pages: 92

Brand: Opel mobile Pages: 76

Capsat TT-3060A

Brand: Thrane&Thrane Pages: 182

Clarity Series BG1200-G

Brand: Transense Pages: 14

Brand: Sony Ericsson Pages: 80

Brand: Qubo Pages: 34

Brand: AMGOO Pages: 14

Brand: Xiaomi Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands