22
GB
O R I G I N A L I N S T R U C T I O N S
When cutting is complete, hold the tool still, release the pressure on the switch and wait until the spinning of the disc has stopped
completely. Lift the cutting head. Disconnect the power cord plug from the power outlet and start maintenance works.
MAINTENANCE, STORAGE AND TRANSPORT
CAUTION! Before carrying out any adjustment, servicing or maintenance work, unplug the tool from the power outlet. Having
fi
nished working with the workpiece/material, inspect the power tool for damage by visually inspecting the exterior and the body
and the handles. Check the power cord, the plug, the action of the ON/OFF switch, the vents for clogging, the motor brushes for
sparking, the noise of the bearings and the drive transmission, and how the power tool starts and runs. During the warranty period,
the user is not allowed to install any power tools or replace any components or parts, as this will void the warranty rights. Any
abnormality found during this inspection or the operation require servicing at an authorized service agent’s. Having
fi
nished your
work, clean the housing, the vents, all switches, all handles and guards with compressed air at 0.3 MPa maximum, a brush or a
dry cloth. Do not use any chemicals or cleaners. Clean the tools and chucks with a clean, dry cloth.
The product should be stored thoroughly cleaned and dried. Store the product indoors. Secure against unauthorized access.
Ensure adequate ventilation to prevent water vapour condensation at the place of storage. The place of storage should protect
the product from weather conditions.
The product should be transported in unit packaging or other hard packaging, providing protection against shocks. Protect the
product from moisture during transport.
When replacing the disc or more frequently, especially if symptoms such as leaking spark shield interiors, dust, uneven rotation,
increased vibration are observed during unloaded operation, thoroughly clean the inside of the guard. To do this, remove the cutter
base, then remove all latches located on the edge of the guard (XX). This will open the guard cover (XXI). Remove the disc and
clean the inside of the guard with a soft-bristle or plastic brush. Do not use sharp or metal objects for cleaning the guard. After
cleaning, close the guard and secure it with the latches.
Spare parts
For a detailed list of spare parts for the appliance go to the “Download” section in the Product tab on the TOYA SA website: www.
toya.pl.
Summary of Contents for YT-82158
