13
O R I G I N A L I N S T R U C T I O N S
GB
PRODUCT CHARACTERISTICS
The wall chaser is a type of electric cutter, which with the help of diamond cutting discs, allows making cuts in the
fl
oor made of
ceramic materials (e.g., concrete, brick, gypsum) in a straight line. Thanks to the possibility of attaching two discs, the
fl
oor after
cutting between the gaps should be removed with a chisel (not included with the tool) or a forcing tool, forming a chase which can
be used to lay pipes: water, gas, electric cables, etc. The wall chaser is a power tool supplied with one-phase alternating current.
The correct, reliable, and safe operation of the tool depends on its proper use, therefore:
Read this entire manual before the
fi
rst use of the tool and keep it for future reference.
The supplier shall not be liable for any damage resulting from failure to comply with the safety instructions and recommendations
speci
fi
ed in this manual.
ACCESSORIES
The wall chaser is delivered with two cutting discs. Before starting work, the tool requires the preparatory steps described later
in this manual.
TECHNICAL DATA
Parameter
Unit
Value
Catalogue No.
YT-82015
Power supply voltage
[V~]
230 - 240
Power frequency
[Hz]
50
Rated power
[W]
1700
Insulation class
II
Rated speed
[min
-1
]
10500
Cutting depth
[mm]
0 - 28
Max. cutting width
[mm]
30
Cutting disc
Outer diameter
[mm]
125
Inner diameter
[mm]
22.2
Max. thickness
[mm]
1.9
Spindle thread size
M14
Weight
[kg]
2.4
Noise level
- sound pressure L
pA
± K
pA
[dB(A)]
93.0 ± 3.0
- sound power L
wA
± K
wA
[dB(A)]
105.0 ± 3.0
Vibration Level a
h
± K
[m/s
2
]
2.8 ± 1.5
Protection rating
IP20
GENERAL SAFETY CONDITIONS
NOTE!
Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock,
fi
re or injuries. The
notion of electric tool used in the instructions applies to all the tools which are powered with electric current, both wire tools and
wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean.
Disorder and poor illumination may be a cause of accidents.
Do not work with electric tools in explosive environments, or those which contain in
fl
ammable liquids, gases or vapours.
Electric tools generate sparks, which may cause a
fi
re in case of contact with in
fl
ammable gases or vapours.
Do not allow children and outsiders to the place of work.
A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must
fi
t the mains socket. Do not modify the plug. Do not use any adapters what-
soever in order to adapt the plug to the socket.
Unmodi
fi
ed plug which
fi
ts the socket reduces the risk of an electric shock.
Avoid contact with grounded surfaces, such as pipes, heaters and refrigerators.
Grounding of the body increases the risk
of an electric shock.
Summary of Contents for YT-82015
