14
O
P
E
R
A
T
I
N
G
M
A
N
U
A
L
GB
at least 1,38 MPa.
If the product features the ability to change the direction of air outlet, direct it away from the human body. Prolonged exposure
to a stream of compressed air can lead to a cooling of place reached by the stream of compressed air, which can cause serious
injuries.
Check the correctness of connection and operation by applying the tool outlet to a piece of wood or wood-based material and by
pressing the trigger once or twice.
Filling the magazine (V)
Note! The magazine should be fi lled only when the product is disconnected from the compressed air supply.
Only fasteners listed in the user manual may be used.
When fi lling, hold the tool in such a way that the outlet is not directed towards the user or towards others.
When fi lling, do not hold your fi nger on the trigger.
YT-09201, YT-09202, YT-09203
Press the magazine latch and pull out the pusher.
Insert the package of fasteners and push in the pusher so that it pushes fasteners towards the face of magazine and then it is
secured with a latch.
Do not use diff erent types and/or diff erent sizes of fasteners in one magazine cartridge.
YT-09211
Pull back the latch of cover of fastener feed mechanism and open the cover. Then open the magazine cover.
The magazine features a raised fl oor that facilitates the transport of shorter fasteners. In order to change the position of the mag-
azine fl oor, turn the magazine’s axle counter-clockwise, change the height of the magazine fl oor, and then turn the magazine’s
axle clockwise. Make sure that the magazine fl oor has been locked in its position and that it is not possible to change the position.
Grab the axle and check if the position of the magazine fl oor can be changed.
Possible positions of the magazine fl oor are marked on the magazine’s wall.
Put the fastener belt onto the magazine’s axle, some of the fasteners intended for nailing should be directed towards the magazine
fl oor. Free end of the belt should be directed towards the outlet of fasteners.
Splines of the feed mechanism should be placed between the fi rst and second fasteners, and the fastener heads should stay in
the guide located above the feed mechanism cover.
Close the magazine cover and then secure it by closing and securing by mans of a latch of a cover of fastener feed mechanism.
Make sure that none of covers opens by itself during the work.
YT-09212 , YT-09213 , YT-09214
Pull back the latch of cover of fastener feeding mechanism and open the cover. Then open the magazine cover.
The magazine features a raised fl oor that facilitates the transport of shorter fasteners. In order to change the position of magazine
fl oor, raise the magazine’s axle and turn it clockwise so that the axle’s spline under the magazine fl oor hooks against the notch
in the inner magazine’s axle (VII). Make sure that the magazine fl oor has been locked in its position and that it is not possible to
change the position. Possible positions of the magazine fl oor are marked on the magazine’s wall.
Put the fastener belt onto the magazine’s axle, some of the fasteners intended for nailing should be directed towards the magazine
fl oor. Free end of the belt should be directed towards the outlet of fasteners. Splines of the feed mechanism should be placed
between the fi rst and second fasteners, and the fastener heads should stay in the guide located above the feed mechanism cover.
Close the magazine cover and then secure it by closing and securing by mans of a latch of a cover of fastener feed mechanism.
Make sure that none of covers opens by itself during the work.
Working with product
The product does not have a trigger lock. This means that a single fastener will be released each time the trigger is pulled.
Subsequent nailing operations can only be carried out after the trigger returns from the neutral position and has been pulled again.
Working with product
The product has a single sequential start system. This means that to start the product, you need to run both the trigger and the
lock.
In such a way that after applying the product to starting place, only a single operation is started after pulling the trigger. Subse-
quent nailing operations can only be carried out after the trigger returns from the neutral position and has been pulled again, while
the lock is kept pressed all the time.
Press the tool in the nailing area and pull the trigger (VI).
If the fastener has been nailed too deep, reduce the pressure in the system every 0.05 MPa until the desired eff ect is achieved.
If the fastener protrudes from the workpiece, increase the pressure in the system every 0.05 MPa until the desired eff ect is
achieved. Do not exceed the maximum pressure for the device.
