YASKAWA VS-616G5 Series, Owner'S Manual, Page: 79 / 84

80
Table A − 4 Constants List (Cont’d)
Constant
No.
Name
(Digital Operator Display)
Initial
Setting
User
Setting
Constant
No.
Name
(Digital Operator Display)
Initial
Setting
User
Setting
H4 − 05 Gain (terminal 23)
(Terminal 23 Gain)
0.50 L6 − 02 Torque detection level 1
(Torq Det 1 Lvl)
150
H4 − 06 Bias (terminal 23)
(Terminal 23 Bias)
0.0 L6 − 03 Torque detection time 1
(Torq Det 1 Time)
0.1
H4 − 07 Analog output signal level selection
(AO Level Select)
0 L6 − 04 Torque detection selection 2
(Torq Det 2 Sel)
0
H5 − 01 Station address
(Serial Comm Adr)
1F L6 − 05 Torque detection level 2
(Torq Det 2 Lvl)
150
H5 − 02 Communication speed selection
(Serial Baud Rate)
3 L6 − 06 Torque detection time 2
(Torq Det 2 Time)
0.1
H5 − 03 Communication parity selection
(Serial Com Sel)
0 L7 − 01 Forward torque limit
(Torq Limit Fwd)
200
H5 − 04 Stopping method after communication error
(Serial Fault Sel)
3 L7 − 02 Reverse torque limit
(Torq Limit Rev)
200
H5 − 05 Communication error detection selection
:
(Serial Flt Dtct)
1 L7 − 03 Forward regenerative torque limit
(Torq Lmt Fwd Rgn)
200
L1 − 01 Motor protection selection
(MOL Fault Select)
1 L7 − 04 Reverse regenerative torque limit
(Torq Lmt Rev Rgn)
200
L1 − 02 Motor protection time constant
(MOL Time Const)
1.0 L8 − 01 Protect selection for internal DB resistor
(DB Resistor Prot)
0
L2 − 01 Momentary power loss detection
(PwrL Selection)
0 L8 − 02 Overheat pre − alarm level
(OH Pre − Alarm Lvl)
95
L2 − 02 Momentary power loss ridethru time
(PwrL Ridethru t)
2.0
[
L8 − 03 Operation selection after overheat pre − alarm
(OH Pre − Alarm Sel)
3
L2 − 03 Min. baseblock time
(PwrL Baseblock t)
0.5
[
L8 − 05 Input open − phase protection selection
(Ph Loss In Sel)
0
L2 − 04 Voltage recovery time
(PwrL V/F Ramp t)
0.3
[
L8 − 07 Output open − phase protection selection
(Ph Loss Out Sel)
0
L2 − 05 Undervoltage detection level
(PUV Det Level)
546 o1 − 01 Monitor selection
(Monitor Select)
6
L3 − 01 Stall prevention selection during accel
(StallP Accel Sel)
1 o1 − 02 Monitor selection after power up
(Power − On Monitor)
1
L3 − 02 Stall prevention level during accel
(StallP Accel Lvl)
150 o1 − 03 Frequency units of reference setting and monitor
(Display Scaling)
0
L3 − 03 Stall prevention limit during accel
(StallP CHP Lvl)
50
]
o1 − 04 Frequency units of constant setting
(Display Units)
0
L3 − 04 Stall prevention selection during decel
(StallP Decel Sel)
1 o1 − 05 Constant No. display selection
(Address Display)
0
L3 − 05 Stall prevention selection during running
(StallP Run Sel)
1 o2 − 01 LOCAL/REMOTE key enable/disable
(Local/Remote Key)
1
L3 − 06 Stall prevention level during running
(StallP Run Level)
160 o2 − 02 STOP key during control circuit terminal operation
(Oper STOP Key)
1
L4 − 01 Speed agree detection level
(Spd Agree Level)
0.0 o2 − 03 User constant initial value
(User Defaults)
0
L4 − 02 Speed agree detection width
(Spd Agree Width)
2.0 o2 − 04 kVA selection
(Inverter Model #)
48
[
L4 − 03 Speed agree detection level (+/ − )
(Spd Agree Lvl + − )
0.0 o2 − 05
Frequency reference setting method selection
:
(Operator M.O.P.)
0
L4 − 04 Speed agree detection width (+/ − )
(Spd Agree Wdth + − )
2.0 o2 − 06
Operation selection when digital operator is disconnected
(Oper Detection)
0
L4 − 05 Operation when frequency reference is missing
(Ref Loss Sel)
0 o2 − 07 Cumulative operation time setting
(Elapsed Time Set)
−
L5 − 01 Number of auto restart attempts
(Num of Restarts)
0 o2 − 08 Cumulative operation time selection
(Elapsed Time Run)
0
L5 − 02 Auto restart operation selection
(Restart Sel)
0 o2 − 09 Initialize mode selection
:
(Init Mode Sel)
2
#
L6 − 01 Torque detection selection 1
(Torq Det 1 Sel)
0
:
Not displayed for some models depending on software version No.
[
Setting unit and initial setting differ depending on inverter capacity.
]
Differs depending on the control method selection (A1 − 02).
# Differs depending on area.