background image

7  Modbus TCP/IP Messaging

EN 36

 

YASKAWA ELECTRIC

 TOBP C730600 59A V1000 Option Modbus TCP/IP Installation Manual

u

Enter Command Types

The drive supports two types of Enter Commands as shown in the table below. An Enter 

Command is enabled by writing 0 to register number 0900H or 0910H. 

Table 11  Enter Command Types

Note:

Because the EEPROM can be written to a maximum of 100,000 times, refrain from frequently 

writing to the EEPROM. An Enter Command is not required if reference or broadcast data are 

sent to the drive.

u

Enter Command Settings

When replacing earlier Yaskawa drive models with a 1000 Series drive and keeping the 

MEMOBUS/Modbus communications settings, parameter H5-11 needs to be set in 

accordance with how the Enter Command functions in the older drive. H5-11 determines if 

an Enter Command is needed or not in order to activate parameter changes in the drive.

• If upgrading from a G7 or F7 series drive to 1000 Series, set parameter H5-11 to 0.

• If upgrading from a V7 series drive to 1000 Series, set parameter H5-11 to 1.

n

H5-11 and the Enter Commands

Table 12  Enter Command Types

Register Number

Description

0900H

Writes data into the EEPROM (non-volatile memory) of the drive and enables the data to 
RAM at the same time. Parameter changes remain even if the power supply is cycled.

0910H

Writes data in the RAM only. Parameter changes are lost when the drive is shut off.

H5-11 Settings

H5-11 = 0

H5-11 = 1

Drive being replaced.

G7, F7

V7

How parameter settings are 
enabled.

When the Enter Command is received 
from the master.

As soon as the value is changed.

Upper/lower limit check.

Upper/lower limit check is performed 
taking the settings of related parameters 
into account.

The upper/lower limit of the changed 
parameter is checked only.

Default value of related 
parameters.

Not affected. The settings of related 
parameters remain unchanged. Parameters 
must be changed manually if needed.

The default settings of related parameters 
are changed automatically.

Error handling when setting 
multiple parameters.

Data is accepted even if one setting is 
invalid. The invalid setting will be 
discarded. No error message occurs.

Error occurs if only one setting is invalid. 
All data sent is discarded.

Summary of Contents for PROFINET V1000















































Reviews: