background image

 

 

Subject: Example Code Manual 

Product: MP2000iec 

Doc#:    EM.MCD.09.095 

Title: Example Code Manual for Linear Flying Shear on MP2300Siec Sigma-5 Demo using camming 

 

 

 

 

        July 13, 2009 

Page 10

 

of

 

21

 

 

4) Flip DI1 on and off. This is to home the slave axis. On starting up, the slave axis is already in its home 

position. 

5) Turn on DI2. This will start the master axis jog. The master axis will jog at 90 degrees /second. To stop the 

master jog, turn DI2 off. 

6) When DO2 lights up, it is an indication that the controller program is ready for registration. 

7) Flip SI4 on the first row on and off. This simulates a part or registration mark. DO2 will turn off. The slave axis 

will wait for the master axis to turn 180 degrees (distance from sensor to shear’s home) from where the mark 

was seen and then start the cam profile. The slave axis travel one way is 250 mm or 2.5 revs on the demo. 

When the slave passes 30 mm travel, DO2 turns on and indicates that the system is ready for another mark. 

DO2 will be on until the window is closed (240 mm on the slave). The slave’s shift in profile during the travel back 

to home will depend on when the registration was seen in the cycle. If the part was detected early (closer to 30 

mm), the move back on the slave will be rapid. If the part was detected later (closer to 240 mm), the move back 

will be slow. 

If a part is not detected while the slave is synchronized to the master and the window is over (DO2 turns off), the 

slave cams out and stays at the home position until the next part comes along. The system will be ready for 

registrations (DO2 on) as soon as the cam out is done. 

 

 

 

 

 

 

 

 

 

Summary of Contents for MP2000iec






















Reviews: