manualshive.com logo in svg

YASKAWA E-S Series, Product Manual

The YASKAWA E-S Series product manual is a comprehensive guide designed for users to easily navigate their way through the functions and features of this advanced product. Download this manual for free from our website and discover how to maximize the potential of your YASKAWA E-S Series device.

Share
Download
background image

5.4  Settings That Must Be Adjusted to the System 

5.4.5  Motor Overload Detection Level

5-28

Linear Coordinates

For a ball screw or other equipment with linear coordinates, set PnB20 to 0, set the forward 
software limit (P-LS) in PnB21, and set the reverse software limit (N-LS) in PnB23.

An error will occur if the positioning target point exceeds a software limit.

An error will also occur if ±INFINITE is specified for the target position in the program table.

If the motor reaches a software limit during jog speed table operation, the motor will be 
stopped at the deceleration rate set in PnB2B.

If you set both PnB21 and PnB23 to 0, the software limits are disabled.

The software limits are enabled when homing is completed. However, if PnB31 is set to 0 
(operate without homing), the software limits are enabled as soon as the power supply is 
turned ON.

Rotational Coordinates

For a rotary table or other equipment with rotational coordinates, set PnB20 to 1 (shortest 
path), 2 (always forward), or 3 (always reverse). Set the last rotational coordinate in PnB21 and 
the first rotational coordinate in PnB23.

The software limits are disabled.
If PnB20 is set to 1 (shortest path) and an absolute position is specified for the positioning 
position, either forward or reverse rotation will be used, whichever is shorter.
If PnB20 is set to 2 (always forward) and an absolute position is specified for the positioning 
position, forward rotation will always be used.
If PnB20 is set to 3 (always reverse) and an absolute position is specified for the positioning 
position, reverse rotation will always be used.
If a relative position is specified, rotation will be in the specified direction regardless of the set-
ting of the parameter.

If a rotary table or other device with rotational coordinates is used, but mutiturn operation is not 
possible, use linear coordinates (PnB20 = 0).
In this case, PnB21 and PnB23 are for software limits.

5.4.5

Motor Overload Detection Level

The motor overload detection level is the threshold used to detect overload alarms and over-
load warnings when the Servomotor is subjected to a continuous load that exceeds the Servo-
motor ratings. 

It is designed to prevent Servomotor overheating. 

You can change the detection timing for A.910 warnings (Overload) and A.720 alarms (Contin-
uous Overload). You cannot change the detection level for A.710 alarms (Instantaneous Over-
load). 

Forward software limit 
(P-LS): PnB21

Reverse software limit 
(N-LS): PnB23

Workpiece

Example

•

PnB21 = +3,599 and PnB23 = 0

•

PnB21 = +4,999 and PnB23 = -5,000

PnB23 = 0

PnB21 = +3599

 

 

PnB23 = -5000

PnB21 = +4999

 

 

Starting point

Starting point

Summary of Contents for E-S Series

































































































































































































































































































Reviews:

No comments

Related manuals for E-S Series

Bardac 400 Product Manual preview
400
Brand: Bardac Pages: 8
Lenze L-force EWS0069 Mounting Instructions preview
L-force EWS0069
Brand: Lenze Pages: 12
ZIEHL-ABEGG Fcontrol Basic FSDM Series Operating Instructions Manual preview
Fcontrol Basic FSDM Series
Brand: ZIEHL-ABEGG Pages: 30
TR-Electronic MP-200 User Manual preview
MP-200
Brand: TR-Electronic Pages: 153
Leadshine EM522-CAN User Manual preview
EM522-CAN
Brand: Leadshine Pages: 33
Rockwell Automation Allen-Bradley PowerFlex 40 22B-B8P0N104 User Manual preview
Allen-Bradley PowerFlex 40 22B-B8P0N104
Brand: Rockwell Automation Pages: 160
Rockwell Automation Allen-Bradley IMPACT 1336 Series Troubleshooting Manual preview
Allen-Bradley IMPACT 1336 Series
Brand: Rockwell Automation Pages: 196
IKEA SILVERGLANS Manual preview
SILVERGLANS
Brand: IKEA Pages: 48
WEG CFW-09 User Manual preview
CFW-09
Brand: WEG Pages: 362
LinMot C1251-2S Installation Manual preview
C1251-2S
Brand: LinMot Pages: 22
LinMot 0150-2656 Installation Manual preview
0150-2656
Brand: LinMot Pages: 24
E-Z Anchor Puller HERO Series Installation, Operation, Maintenance & Warranty Information preview
HERO Series
Brand: E-Z Anchor Puller Pages: 19
REXROTH EcoDrive Cs Project Planning Manual preview
EcoDrive Cs
Brand: REXROTH Pages: 230
YASKAWA CIMR-AC4A WAA Series Quick Start Manual preview
CIMR-AC4A WAA Series
Brand: YASKAWA Pages: 38
Fagor 2104 Quick Reference preview
2104
Brand: Fagor Pages: 84
Danfoss VLT CANopen MCA 105 Programming Manual preview
VLT CANopen MCA 105
Brand: Danfoss Pages: 50
Circutor PLC PRIME Instruction Manual preview
PLC PRIME
Brand: Circutor Pages: 72
Wavelength Electronics QCL1000 LAB Manual preview
QCL1000 LAB
Brand: Wavelength Electronics Pages: 21

Brands by name

Popular brands

Load more brands