YASKAWA CIPR-GA50C series, Technical Manual

Page: 599 / 766

Parameter
Details
12
12.8 H: Terminal Function Selection
YASKAWA SIEPC71061753A GA500 Technical Manual 599
12.8 H: Terminal Function Selection
H parameters set functions for external input and output terminals.
◆
H1: Digital Inputs
H1 Parameters set the MFDI terminal functions.
■
H1-01 to H1-07 Terminal S1 to S7 Function Selection
The drive has 7 MFDI terminals. Refer to Table 12.54 for drive default settings and functions.
Table 12.54 MFDI Default Settings and Functions
No. Name Default Function
H1-01 Terminal S1 Function Selection 40 (F)
*1
Forward RUN (2-Wire)
H1-02 Terminal S2 Function Selection 41 (F)
*1
Reverse RUN (2-Wire)
H1-03 Terminal S3 Function Selection 24 External Fault (NO-Always-Coast)
H1-04 Terminal S4 Function Selection 14 Fault Reset
H1-05 Terminal S5 Function Selection 3 (0)
*1
Multi-Step Speed Reference 1
H1-06 Terminal S6 Function Selection 4 (3)
*1
Multi-Step Speed Reference 2
H1-07 Terminal S7 Function Selection 6 (4)
*1
Jog Reference Selection
*1 The value in parentheses identifies the default setting when you set A1-03 = 3330 [Initialize Parameters = 3-Wire Initialization] .
Refer to the and use H1-xx [MFDI Function Select] to set the function.
Refer to the Table 12.55 and use H1-xx [MFDI Function Select] to set the function.
Table 12.55 MFDI Setting Values
Setting Value Function Reference
0
*1
3-Wire Sequence
602
1 LOCAL/REMOTE Selection 603
2 External Reference 1/2 Selection
604
3 Multi-Step Speed Reference 1
604
4 Multi-Step Speed Reference 2
604
5 Multi-Step Speed Reference 3 604
6 Jog Reference Selection
604
7 Accel/Decel Time Selection 1
604
8
*1
Baseblock Command (N.O.)
604
9
*1
Baseblock Command (N.C.) 605
A Accel/Decel Ramp Hold
605
B Overheat Alarm (oH2)
605
C Analog Terminal Enable Selection
605
E ASR Integral Reset 606
F Through Mode
606
10 Up Command
606
11 Down Command
607
12
*1
Forward Jog 608
13
*1
Reverse Jog
608
14 Fault Reset
608
15
*1
Fast Stop (N.O.)
609
16 Motor 2 Selection 609
17
*1
Fast Stop (N.C.)
610
18 Timer Function
610
19 PID Disable
610
Setting Value Function Reference
1A Accel/Decel Time Selection 2
610
1B
*2
Programming Lockout 610
1E Reference Sample Hold
611
20 to 2F
*1
External fault
611
30 PID Integrator Reset
612
31 PID Integrator Hold 612
32 Multi-Step Speed Reference 4
612
34 PID Soft Starter Disable
612
35 PID Input (Error) Invert
613
3E PID Setpoint Selection 1 613
3F PID Setpoint Selection 2
613
40
*1
Forward RUN (2-Wire)
613
41
*1
Reverse RUN (2-Wire)
613
42
*1
Run Command (2-Wire Sequence 2) 614
43
*1
FWD/REV (2-Wire Sequence 2)
614
44 Add Offset Frequency 1 (d7-03)
614
45 Add Offset Frequency 2 (d7-03)
614
46 Add Offset Frequency 3 (d7-03) 614
47 Node Setup (CANopen) 614
60 DC Injection Braking Command
615
61 Speed Search from Fmax
615
62 Speed Search from Fref 615
63 Field Weakening
615
65
*1
KEB Ride-Thru 1 Activate (N.C.)
615
66
*1
KEB Ride-Thru 1 Activate (N.O.)
616