Yard force SA600H Page 32 Original Instructions Manual Download

Page: 32 / 33

No. Message

Type of

message

Symptom

Action

EF8

Warning

message

Battery voltage is
too low to perform
normal mowing

1. Normally if voltage is low, the mower

should automatically return to the
charging station.

2. If not, please carry your mower

manually to charging station when it
has stopped on the lawn.

EF9

Warning

message

Drive motor maybe
locked

Power off then restart the mower. If the
fault still exists, please call after sales
service.

EF10

Warning

message

Cutting motor may
be locked

Fault

message

Micro-controller
core self-check
fault

Fault

message

Cutting motor
stops in use, but
it cannot stop
when switched off
or cutting motor
overloaded.

Fault

message

Drive motor cannot
stop when mower
stops.

E20

Fault

message

Boundary signal
self-checking error

E21/E22

Fault

message

Micro-controller
self-checking error

E23

Fault

message

Driving motor
cannot turn when
mower is started

E24

Fault

message

Cutting Driving
motor cannot turn
when mower is
started

Hot key

Hot key operation

Function

Display software version number

Active pin code

Active PUK code

Display fault time and fault code

Display product serial number

Open and close rain sensor

SET

START

SET

START

SET

TROUBLESHOOTING

Summary of Contents for SA600H


































Search results

Summary of Contents for SA600H

Reviews:

Related manuals for SA600H

Brands by name

Popular brands

Yard force SA600H, Original Instructions Manual

Search results

Summary of Contents for SA600H

Reviews:

Related manuals for SA600H

Brands by name

Popular brands