background image

44

45

Battery and charging

  This symbol means the battery has a remain capacity of 100%.

 

This symbol means the battery has a remain capacity of 75%.

 

This symbol means the battery has a remain capacity of 50%.

 

This symbol means the battery has a remain capacity of 30%.

 

   This symbol means the battery is empty.

 

    (Sustained)  Mower is going back to charging station to get charged.

 

    (Flash)  Mower is charging on charging station

 

   (Flash)  

 (Sustained)  When mower is on charging station, This means is 

battery is fully charged and charging finish.

Touch screen and input

 

          Touch screen is locked

  

       Input normally Pincode to unlock touch screen

 

  Input new pincode  when you change normally pincode

 

 Input new pincode again when you change normally pincode

Others

 

  You select boundary signal S1

  

  You select boundary signal S2

  

  STOP Key is pressed , Mower stop to cut

Security PIN code

 

When switch on the machine, Robomower are locked with a factory setting PIN code. Please 
press the graphic of a lock, then the PIN code input screen will display.

              

Press the blank frame right near “0” 4 times to unlock the Robomower 
NOTE: The default PIN code is “0000” 

Setting 

Set Date and Time

 

Start

Home

Set

  

 

Start

Home

Set

       

         

Press the button of “SET” on the left side of the touch screen, then press button 

  . The 

date and time number will flash. Adjust year and date number by pressing button of  

  

and 

 , when the correct nummer display, press the button of “SET” then move to next 

number adjustment. 
After setting settled, screen will automaticly quit date and time setting in 15 seconds, or you 
may touch anywhere on the touch screen to finalize the date and time setting. 

Note: only when the date and time setting correctly, will the Robomower work properly.

OPERATION

OPERATION

Summary of Contents for SA600H


































Reviews: