Klomby z kwiatami
Przewód graniczny należy zastosować do wyłączenia ze strefy koszenia jakichkolwiek klombów.
Dwa odcinki przewodu granicznego między klombem a zewnętrzną krawędzią koszonego terenu
można poprowadzić na dwa sposoby:
1) Poprowadzić przewody tak, aby odległość między nimi wynosiła ponad 5 cm. Robokosiarka
rozpozna je wówczas jako zwykłą przeszkodę. Podczas koszenia będzie się od nich w
standardowy sposób „odbijać”. Jadąc wzdłuż przewodu granicznego z powrotem do stacji
ładowania kosiarka objedzie wtedy klomb.
2) Innym rozwiązaniem jest dopilnowanie, aby odległość między dwoma równoległymi przewodami
wynosiła nie więcej niż 5 cm. Przewodów nie należy jednak między sobą krzyżować - patrz niżej. W
tym wariancie robokosiarka nie rozpozna przewodów i po prostu po nich przejedzie. Przy takim
rozwiązaniu konieczne jest umieszczenie jakiejś przeszkody na przewodzie granicznym
biegnącym wokół klombu. Przeszkodę tę, np. duży kamień lub palik, należy umieścić w pobliżu
punktu A zaznaczonego na ilustracji poniżej. Przeszkoda musi się znajdować w płaskim miejscu o
wymiarach około 1 m x 1 m i nie na pochyłości. Przeszkoda ta umożliwi maszynie opuszczenie koła.
Oczka wodne i baseny
O ile robokosiarka jest zabezpieczona przed deszczem i bryzgami wody, o tyle zanurzenie jej w
wodzie doprowadzi do poważnego uszkodzenia podzespołów elektronicznych.
Dlatego też absolutnie koniecznie należy oddzielić jakiekolwiek baseny od strefy koszenia za
pomocą przewodu granicznego. W celu zwiększenia poziomu bezpieczeństwa zalecamy
ustawienie wokół basenu płotu.
Korytarze graniczne
Jeśli w obrębie strefy koszenia powstały korytarze graniczne, powinny one mieć szerokość co
najmniej 2 m i nie powinny być dłuższe niż maksymalnie 8 m.
Jeśli korytarz będzie za wąski lub za długi, robokosiarka może nie być w stanie manewrować i
przejechać z jednego końca na drugi.
Podłączenie stacji ładowania do przewodu granicznego
Stację ładowania należy ustawić na końcu przewodu granicznego, tak aby przewód biegł
wzdłużnie przez środek stacji ładowania. Jego koniec należy podłączyć do lewej (czarnej) łączówki
oznaczonej literą „F” (ang. front – przód). Drugi koniec należy podłączyć do prawej (czerwonej)
łączówki oznaczonej literą „B” (ang. back – tył).
Gdy tylko niebieska dioda LED potwierdzi, że wszystko jest w porządku, należy przetestować
działanie robokosiarki. Podczas mocowania przewodu granicznego należy sprawdzać, czy dioda
LED świeci, aby wykluczyć ewentualne przerwania połączenia. Ustawić robokosiarkę w strefie
pracy, kilka metrów od stacji ładowania i włączyć.
Najpierw naciśnij przycisk
, a następnie
, kilka sekund później kosiarka zautomatyzowana
powinna automatycznie wrócić do stacji dokującej, lokalizując przewód ograniczający w kierunku
przeciwnym do ruchu wskazówek zegara i podążając za nim. Jeśli kosiarka zautomatyzowana nie
zadokuje prawidłowo, ustaw stację dokującą w bardziej odpowiedniej pozycji.
PL
PL
6
7
> 5 cm
>5 cm
< 5 cm
<5cm
A
< 8 m
> 2 m