background image

 

General information

 

2

 

EMU25262

 

Manufactured date label

 

This label is attached to the clamp bracket or
the swivel bracket.

 

EMU25272

 

Star labels

 

Your outboard motor is labeled with a Cali-
fornia Air Resources Board (CARB) star la-
bel. See below for a description of your

particular label.

 

EMU25280

 

One Star—Low Emission

 

The one-star label identifies engines that
meet the Air Resources Board’s 2001 ex-
haust emission standards. Engines meeting
these standards have 75% lower emissions
than conventional carbureted two-stroke en-
gines. These engines are equivalent to the
U.S. EPA’s 2006 standards for marine en-
gines.

 

EMU25290

 

Two Stars—Very Low Emission

 

The two-star label identifies engines that
meet the Air Resources Board’s 2004 ex-
haust emission standards. Engines meeting
these standards have 20% lower emissions
than One Star-Low-Emission engines.

 

1. Manufactured date label location

ZMU05236

1

ZMU04931

Manufactured:

ZMU04346

 

1. Star labels location

ZMU04932

1

ZMU01702

✩✱✣✬✤✧✲✣ ✥   

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for Z250
























































































Reviews: