manualshive.com logo in svg

Yamaha Z250, Owner'S Manual

Share
Download
Yamaha Z250 Owner'S Manual Download Page 62

 

Maintenance

 

57

 

Checkpoints

 

●

 

Fuel system parts leakage

 

●

 

Fuel line joint leakage

 

●

 

Fuel line cracks or other damage

 

●

 

Fuel connector leakage

 

EMU28980

 

Inspecting fuel filter

WARNING

 

EWM00310 

 

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

 

●

 

If you have any question about properly
doing this procedure, consult your
Yamaha dealer.

 

●

 

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

 

●

 

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

 

●

 

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

 

●

 

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion

 

hazard.

 

EMU29012

 

Cleaning fuel filter

 

1.

Lift up and hold the locking tab to loosen
the filter cup ring nut.

ZMU01853

ZMU01955

✩✱✣✬✤✧✲✣ ✪   

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for Z250
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands