background image

 

Maintenance

 

52

 

hose.

4.

When flushing is complete, reinstall the
garden hose connector on the fitting on
the bottom cowling. Tighten the connec-
tor securely.

CAUTION:

 

ECM00540 

 

Do not leave the garden hose connector
loose on the bottom cowling fitting or let
the hose hang free during normal opera-
tion. Water will leak out of the connector
instead of cooling the engine, which can
cause serious overheating. Be sure the
connector is tightened securely on the fit-

 

ting after flushing the engine.

NOTE:

 

 

When flushing the engine with the boat in
the water, tilting up the outboard motor un-
til it is completely out of the water will
achieve better results.

 

 

For cooling system flushing instructions,

 

see page 48.

 

EMU28450

 

Cleaning the outboard motor

 

After use, wash the exterior of the outboard
motor with fresh water. Flush the cooling
system with fresh water.

NOTE:

 

For cooling system flushing instructions, see

 

page 48.

 

EMU28460

 

Checking painted surface of motor

 

Check the motor for scratches, nicks, or flak-
ing paint. Areas with damaged paint are
more likely to corrode. If necessary, clean
and paint the areas. A touch-up paint is avail-
able from your Yamaha dealer.

 

EMU28486

 

Periodic maintenance

WARNING

 

EWM01070 

 

Be sure to turn off the engine when you
perform maintenance unless otherwise
specified. If you or the owner is not famil-
iar with machine servicing, this work
should be done by your Yamaha dealer or

 

other qualified mechanic.

Maintenance, replacement, or repair of
the emission control devices and sys-
tems may be performed by any marine
engine repair establishment or individual.
All warranty repairs, however, including
those to the emission control system,
must be performed by an authorized
Yamaha marine dealership.

 

A service manual is available for purchase
through your Yamaha dealer for owners who
have the mechanical skills, tools, and other
equipment necessary to perform mainte-
nance not covered by this owner’s manual.

 

EMU28510

 

Replacement parts

 

If replacement parts are necessary, use only
genuine Yamaha parts or parts of the same
type and of equivalent strength and materi-
als. Any part of inferior quality may malfunc-
tion, and the resulting loss of control could
endanger the operator and passengers.
Yamaha genuine parts and accessories are
available from your Yamaha dealer.

ZMU02550

✩✱✣✬✤✧✲✣ ✥   

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for Z250
























































































Reviews: