manualshive.com logo in svg

Yamaha Z250, Owner'S Manual

Share
Download
Yamaha Z250 Owner'S Manual Download Page 50

 

Operation

 

45

 

EMU28060

 

Cruising in shallow water

 

The outboard motor can be tilted up partially
to allow operation in shallow water.

 

EMU28090

 

Power trim and tilt models / power tilt 
models

 

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

 

EWM00660 

 

●

 

Place the gear shift in neutral before
setting up for shallow water cruising.

 

●

 

Return the outboard motor to its normal
position as soon as the boat is back in

 

deeper water.

CAUTION:

 

ECM00260 

 

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-

ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

 

ing can result.

 

EMU28184

 

Procedure for power trim and tilt / power
tilt models

 

1.

Place the gear shift lever in neutral.

2.

Slightly tilt the outboard motor up to the
desired position using the power trim / tilt
switch.

ZMU04603

DN

DN

ZMU01979

N

ZMU04588

UP

ZMU01935

UP

DN

✩✱✣✬✤✧✲✣ ✧   

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for Z250
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands