manualshive.com logo in svg

Yamaha YFM35RX, Owner'S Manual

The Yamaha YFM35RX Owner's Manual is a comprehensive guide for users of this powerful off-road vehicle. This indispensable manual provides detailed instructions, important safety information, and maintenance tips to ensure optimal performance. Download your free manual from our website and unleash the full potential of your Yamaha YFM35RX.

Share
Download
background image

5-1

5

EBU19200

PRE-OPERATION CHECKS

EBU19222

Pre-operation check list 

Before operating this ATV, be sure to check the items listed in the following table.

WARNING

EWB00480

Always inspect your ATV each time you use it to make sure it is in safe operating condition.
Always follow the inspection and maintenance procedures and schedules described in the Owner’s
Manual. Failure to inspect increases the possibility of an accident or equipment damage.

NOTE:

The maintenance of some items in the table has to be performed by a Yamaha dealer. Refer to the periodic
maintenance charts on page 8-3 to determine which service should be performed by a Yamaha dealer.

ITEM

ROUTINE

PAGE

Fuel

• Check fuel level in fuel tank, and add recommended fuel if neces-

sary.

• Check fuel line for leakage. Correct if necessary.

4-8, 5-3

Engine oil

• Check oil level in engine, and add recommended oil to specified lev-

el if necessary.

• Check ATV for oil leakage. Correct if necessary.

5-3, 8-11

Front brake

• Check operation. If soft or spongy, have Yamaha dealer bleed hy-

draulic system.

• Check brake pads for wear, and replace if necessary.
• Check brake fluid level in reservoir, and add recommended brake 

fluid to specified level if necessary.

• Check hydraulic system for leakage. Correct if necessary.

5-3, 8-22, 8-23, 8-24

U5YT64E0.book  Page 1  Monday, April 9, 2007  1:03 PM

Summary of Contents for YFM35RX







































































































































Reviews:

No comments

Related manuals for YFM35RX

Brands by name

Popular brands

Load more brands