manualshive.com logo in svg

Yamaha YFM35RX, Owner'S Manual, Page: 80 / 134

Share
Download
Yamaha YFM35RX Owner'S Manual Download Page 80

8-2

8

The service information included in this manual
and the tools provided in the owner’s tool kit are in-
tended to assist you in the performance of preven-
tive maintenance and minor repairs. However,
additional tools such as a torque wrench may be
necessary to perform certain maintenance work
correctly.

NOTE:

If you do not have the tools or experience required
for a particular job, have a Yamaha dealer perform
it for you.

WARNING

EWB01850

Never modify this ATV through improper in-
stallation or use of accessories, as it may
cause changes in handling, which in some sit-
uations could lead to an accident. All parts and
accessories added to this ATV should be gen-
uine Yamaha or equivalent components de-
signed for use on this ATV and should be
installed and used according to instructions. If
you have questions, consult an authorized
Yamaha ATV dealer.

U5YT64E0.book  Page 2  Monday, April 9, 2007  1:03 PM

Summary of Contents for YFM35RX







































































































































Reviews:

No comments