Yamaha YFM35RX Owner'S Manual Download

Page: 127 / 134

10-2

Engine oil quantity:

Without oil filter element replacement:

2.50 L (2.64 US qt) (2.20 Imp.qt)

With oil filter element replacement:

2.60 L (2.75 US qt) (2.29 Imp.qt)

Air filter:

Air filter element:

Wet element

Fuel:

Recommended fuel:

Regular unleaded gasoline only (EUR)
Unleaded gasoline only (AUS)(NZL)

Fuel tank capacity:

9.0 L (2.38 US gal) (1.98 Imp.gal)

Fuel reserve amount:

2.7 L (0.71 US gal) (0.59 Imp.gal)

Carburetor:

Manufacturer:

MIKUNI

Type x quantity:

BSR36 x 1

Spark plug (s):

Manufacturer/model:

NGK/DR8EA

Spark plug gap:

0.6–0.7 mm (0.024–0.028 in)

Clutch:

Clutch type:

Wet, multiple-disc

Operation:

Left hand operation

Transmission:

Primary reduction system:

Spur gear

Primary reduction ratio:

76/24 (3.166)

Secondary reduction system:

Chain drive

Secondary reduction ratio:

38/13 (2.923)

Transmission type:

Constant mesh 6-speed.forward, 1-speed.reverse

Operation:

Left foot operation

Gear ratio:

1st:

36/16

20/27

29/18 (2.685)

2nd:

33/20

20/27

29/18 (1.969)

3rd:

29/23

20/27

29/18 (1.504)

4th:

27/26

20/27

29/18 (1.239)

5th:

25/28

20/27

29/18 (1.065)

6th:

23/29

20/27

29/18 (0.946)

Reverse gear:

33/16

33/10 (6.806)

Chassis:

Frame type:

Steel tube frame

U5YT64E0.book Page 2 Monday, April 9, 2007 1:03 PM

Summary of Contents for YFM35RX







































































































































Search results

Summary of Contents for YFM35RX

Reviews:

Related manuals for YFM35RX

Brands by name

Popular brands

Yamaha YFM35RX, Owner'S Manual

Search results

Summary of Contents for YFM35RX

Reviews:

Related manuals for YFM35RX

Brands by name

Popular brands