manualshive.com logo in svg

Yamaha YFM35RX, Owner'S Manual

The Yamaha YFM35RX Owner's Manual is a comprehensive guide for users of this powerful off-road vehicle. This indispensable manual provides detailed instructions, important safety information, and maintenance tips to ensure optimal performance. Download your free manual from our website and unleash the full potential of your Yamaha YFM35RX.

Share
Download
background image

4-12

4

To install the seat

Insert the projections on the front of the seat into
the seat holders and push down on the seat at the
rear.

NOTE:

Make sure that the seat is securely fitted.

EBU18990

Adjusting the front shock absorber as-
semblies 

The spring preload can be adjusted to suit the rid-
er’s weight and the riding conditions.
Adjust the spring preload as follows.
Turn the adjusting ring in direction (a) to increase
the spring preload and thereby harden the suspen-
sion, and in direction (b) to decrease the spring
preload and thereby soften the suspension.

1. Seat lock lever

1. Projection
2. Seat holder

U5YT64E0.book  Page 12  Monday, April 9, 2007  1:03 PM

Summary of Contents for YFM35RX







































































































































Reviews:

No comments

Related manuals for YFM35RX

Brands by name

Popular brands

Load more brands