manualshive.com logo in svg

Yamaha YFM35RX, Owner'S Manual

The Yamaha YFM35RX Owner's Manual is a comprehensive guide for users of this powerful off-road vehicle. This indispensable manual provides detailed instructions, important safety information, and maintenance tips to ensure optimal performance. Download your free manual from our website and unleash the full potential of your Yamaha YFM35RX.

Share
Download
background image

8-23

8

EBU24251

Checking the brake fluid level 

Insufficient brake fluid may allow air to enter the
brake system, possibly causing it to become inef-
fective.
Before riding, check that the brake fluid is above
the minimum level mark and replenish if neces-
sary. A low brake fluid level may indicate worn
brake pads and/or brake system leakage. If the
brake fluid level is low, be sure to check the brake
pads for wear and the brake system for leakage.

Front brake

Rear brake

Observe these precautions:

●

When checking the fluid level, make sure that
the top of the brake fluid reservoir is level.

●

Use only the recommended quality brake fluid,
otherwise the rubber seals may deteriorate,
causing leakage and poor braking performance.

●

Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reaction
and lead to poor braking performance.

1. Minimum level mark

1. Minimum level mark

Recommended brake fluid:

DOT 4

U5YT64E0.book  Page 23  Monday, April 9, 2007  1:03 PM

Summary of Contents for YFM35RX







































































































































Reviews:

No comments

Related manuals for YFM35RX

Brands by name

Popular brands

Load more brands