Yamaha XVS250 2001 Service Manual Download Page 127

Page: 127 / 332

4-17

REAR WHEEL AND REAR BRAKE

CHAS

NOTE:

WARNING

NOTE:

Rear wheel sprocket self-locking
nut

40 Nm (4.0 m

kg)

Tighten the self-locking nuts in stages and in a
crisscross pattern.

EAS00569

CHECKING THE BRAKE
The following procedure applies to all of the
brake shoes.
1. Check:

brake shoe lining
Glazed areas

Repair.

Sand the glazed areas with course sandpa-
per.

After sanding the glazed areas, clean the brake
shoe with a cloth.

2. Measure:

brake shoe lining thickness

Out of specification

Replace.

Brake shoe lining thickness limit
(minimum)

2 mm

Do not allow oil or grease to contact the
brake shoes.

Replace the brake shoes as a set, if either is
worn to the wear limit.

3. Measure:

brake drum inside diameter

Out of specification

Replace the wheel.

Brake drum inside diameter limit
(maximum)

131 mm

Summary of Contents for XVS250 2001













































































































































































































































































































































Search results

Summary of Contents for XVS250 2001

Reviews:

Related manuals for XVS250 2001

Brands by name

Popular brands

Yamaha XVS250 2001, Service Manual

Search results

Summary of Contents for XVS250 2001

Reviews:

Related manuals for XVS250 2001

Brands by name

Popular brands